Author Topic: IGT red white blue (Read 12233 times)

FastEd · « **on:** February 26, 2017, 09:38:10 AM »

I'm a new member, so I hope I'm posting this in the correct place....

I replaced the battery in my IGT s-plus red, white and blue machine. I turned on the machine and
received error 61 in the winner paid window. I then
pushed the test button, next to the power switch, and
then received error 61 1, I then turn the reset key
(right side of machine) and I received a 63 in the
winner paid window. I can't find an error code for
63....

Thanks for any help!!!!
-Ed

erbs · « **Reply #1 on:** February 26, 2017, 09:48:22 AM »

Welcome to NLG.

When you got the 61-1 did you close and latch the door before you turned the key? If not try it with the door closed.

FastEd · « **Reply #2 on:** February 27, 2017, 06:30:49 AM »

Good morning erbs and thanks so much for the welcome to NLG.
After receiving the 61.1, I did close the door before turning the reset key. It returned to 61, so I turned the reset key again and a 63 appeared in the winner paid window. However it appeared in the far right side of the winner paid window as opposed to the 61 and 61.1 which always were on the far left side of the paid window.
I did discover, on the inside of the main door, a list of error codes and it refers to error 63 as "Card Cage Open".
Can't find anything on it, but still trying....

Thanks again,,,,
-Ed

Ken · « **Reply #3 on:** February 27, 2017, 07:03:45 AM »

Since you had the 61-1 and it went back to 61 then a ram clear will need to be done. If there is a bill acceptor then a set chip is needed to reactivate it.

FastEd · « **Reply #4 on:** February 27, 2017, 08:29:06 AM »

Thanks Ken, for responding.

I have both, but it was suggested I use them as a last resort. Well, I guess this is the last resort!!!!

Thanks again for your help....

-Ed

knagl · « **Reply #5 on:** February 27, 2017, 12:56:34 PM »

I think Ken misread your post. Your 61-1 didn't go back to 61, it went to a 63 error.

That said, it won't hurt much to try the clear chip here. If that doesn't do it, we can dig deeper to resolve the issue.

Ken · « **Reply #6 on:** February 27, 2017, 02:41:14 PM »

Quote from: knagl on February 27, 2017, 12:56:34 PM

I think Ken misread your post. Your 61-1 didn't go back to 61, it went to a 63 error.

That said, it won't hurt much to try the clear chip here. If that doesn't do it, we can dig deeper to resolve the issue.

I think I read it correctly

He posted this is reply 2 .. After receiving the 61.1, I did close the door before turning the reset key. It returned to 61, so I turned the reset key again and a 63 appeared in the winner paid window.

FastEd · « **Reply #7 on:** February 27, 2017, 03:42:24 PM »

Hello again,

Well, I installed the clear chip, as instructed. I turned on the power, received one ding and that was it. Nothing else took place. It was my understanding the Spin Reel Button would light. I would select it and the machine would clear and reset. The Spin Reel Button never lit up. Really lost now!!!!

Thanks to all....

-Ed

Ken · « **Reply #8 on:** February 27, 2017, 06:56:20 PM »

After the first ding you have to push and release the self test switch once. Count up to 02 - 999 and then the ram clear is done.

knagl · « **Reply #9 on:** February 27, 2017, 07:00:34 PM »

Ken: my apologies, I was the one who read it wrong. Oops!

Ed: Once you power up the machine with the clear chip installed, press the white self-test button next to the power switch.

Quote

Turn power on and press the white test switch button once. There will be a set of numbers counting up on the door. Once it is at "2 999". Turn power off and replace the original GAME PROM

FastEd · « **Reply #10 on:** February 28, 2017, 06:00:21 AM »

Thanks, I will try the test switch today!!!!

Appreciate all the help!!!!

-Ed

FastEd · « **Reply #11 on:** February 28, 2017, 07:36:19 AM »

I tried the test button after turning on the machine with the clear chip installed. It produced a constant ding until I turned off the power!!!! Is that normal? Should I let it ding or will it ever stop?

Thanks,,,,

-Ed

FastEd · « **Reply #12 on:** February 28, 2017, 08:40:18 AM »

What I meant by "let it ding".... I thought that it my be a part of the counting process.... 2....999

Novice here, at best.... Sorry,,,,

-Ed

rokgpsman · « **Reply #13 on:** February 28, 2017, 09:50:44 AM »

Was the display changing while it was dinging? How long did you let it ding before shutting it off?

FastEd · « **Reply #14 on:** February 28, 2017, 09:56:14 AM »

The winner paid window remained "0". I let I run for 90 seconds before turning off the machine....

-Ed

Shaggy · « **Reply #15 on:** February 28, 2017, 10:45:09 AM »

You do have the chip oriented the in right direction? The notch has to face the same way as the game chip does.

Dave

FastEd · « **Reply #16 on:** February 28, 2017, 10:50:52 AM »

Yes, it's faced the same as the reel chip next to it, notch toward bottom of the board.... Does the hopper have to be in for the clear chip to work?

Thanks,,,,

-Ed

Shaggy · « **Reply #17 on:** February 28, 2017, 11:26:59 AM »

I don't think so. You're just clearing the settings. I know this is old hat....All the chips in good, no bent legs etc. I'm trying to think of a reason the clear is acting up. Board seated well?

FastEd · « **Reply #18 on:** February 28, 2017, 11:44:10 AM »

I double checked the pins and the installation....
All good!!!!

Thanks so much for your efforts,,,,
Greatly appreciated....

-Ed

Ken · « **Reply #19 on:** February 28, 2017, 11:51:15 AM »

Quote from: FastEd on February 27, 2017, 03:42:24 PM

Hello again,

Well, I installed the clear chip, as instructed. I turned on the power, received one ding and that was it. Nothing else took place. It was my understanding the Spin Reel Button would light. I would select it and the machine would clear and reset. The Spin Reel Button never lit up. Really lost now!!!!

Thanks to all....

-Ed

When you did this and the one ding occurred then the self test switch needed to be pushed and released. Then two dings occur and the count up on the display starts.

Besides checking the eprom legs for being bent .. also check the two connectors on the CPU board for bent pins. I don't remember the number of pins in those connectors.

No, the hopper does not have to be installed during a ram clear.

News:

NLG Site Navigation Menu

Author Topic: IGT red white blue (Read 12233 times)