1
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Igt 502 mpu
« Last post by boofytheslotslayer on Today at 05:56:23 AM »I am in need of a 502 board if you have one available still. Please and thank you!
Welcome to the NewLifeGames.com message forum!
|
1
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Igt 502 mpu« Last post by boofytheslotslayer on Today at 05:56:23 AM »I am in need of a 502 board if you have one available still. Please and thank you!
2
IGT S2000 and Vision Games / Re: Display Netplex Link Down and no LEDs on CPU« Last post by Stayouttadabunker on Today at 05:41:46 AM »That was good that you checked the power voltages on the power connecting Molex on the bottom of the backplane.
It certainly shows that your power supply is fine. 1st off, that may just be an informational message and not really an "error"? Try checking that 2-wire black/red power harness that runs down to the VFD driver board attached to the back of the door panel. The driver board is the one with the ribbon cable running up to the VFD display. You will notice it has a black and red 2-pin harness powering it up. Disconnect the 2-pin black harness plastic plug by depressing the housing latch inwards to release it from the header socket. Turn the cabinet's power switch ON, and check with your multimeter the voltage coming out of the harness. Because there's no LEDS coming on you MPU, with the power switch OFF, I'd slide it out an carefuly inspect the pins underneath the MPU if they're bent or touching each other. Also, check the software chips for any folded under pins. Re-install and see if the machine LEDs come back to life....if not, remove the onboard battery and check it's voltage. 3
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: PE+ Fuse Holder« Last post by RobinAK on Today at 05:41:27 AM »I actually found a video on youtube that shows discharging the cap so I've got that under control now. I have not pulled the monitor. I think I'm going to go ahead and just put an LCD in and be done with it. The machine was never put in commercial operation and always used in a private environment so it's in pristine condition that's why I'm going to just bite the bullet and upgrade the monitor. You can send the monitor chassis to K-Lar they can repair the board. 4
Aristocrat Video Gaming Machines / Aristocrat Caribbean Gold II - MK4« Last post by mtgedney on Today at 05:40:39 AM »Greatings all. Long time lurker, first time poster. I picked up a MK4 Caribbean Gold II that is currently working. I've repaired a lot of arcade machines but never dabbled in slot machines. I was surprised there was not more documentation available for these games. No manuals or wiring diagrams, or general information, as it took some time to figure out this was referred to a MK4 or 540 system. Is there a place with more information out there?
This machine powers on, lights up, makes a few sounds but that is it. No display. I was also surprised these were CGA monitors in the mid-90s (is there an isolation transformer in these for the crt?). Any assistance would be appreciated. Thanks. 5
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: 2 - 3902 Boards« Last post by boofytheslotslayer on Today at 05:39:28 AM »ILL TAKE ONE OFF YOUR HANDS. WHERE DO I SEND THE FUNDS TO? THANKS
6
IGT S2000 and Vision Games / Re: S2000 VFD Question« Last post by Stayouttadabunker on Today at 05:25:24 AM »Yes...you can replace that with the more modern VFD (Vacuum Fluorescent Display) version.
The black and red power harness would be plugged instead into the VFD driver board, as well as the 5-pin data harness with the green colored wires. All you would need to do is remove the 2 Philips screws holding the present VFD display, swap it out with the newer type, secure theisplay with the 2 screws, and attach the ribbon cable between the new display and the new driver board. Have fun! 7
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: PE+ Fuse Holder« Last post by John H on Today at 05:23:09 AM »Thanks...and I will.
8
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: IGT S2000 PINBALL« Last post by auto155 on Today at 04:30:55 AM »bump
9
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: IGT S2000 DOUBLE TOP DOLLAR« Last post by auto155 on Today at 04:30:23 AM »bump
10
Bally Electromechanical / Re: Bally 809 ZZB Slot machine hopper help!« Last post by Blainesgames on Today at 03:51:32 AM »Thanks Wolftalk for your help.
|
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |