New Life Games LLC
**Reel Slots** Gaming Machines => IGT S2000 and Vision Games => Topic started by: Caliwebman on January 31, 2018, 09:33:41 PM
-
Wondering if anyone has for sale, or can direct me to the sale of some S2000 Reel strips for White Ice (Backlit). Please see pic attached for details. Also, im wondering about the lines external to the glass on these machines, the 5 line pay lines that wear out and eventually wear off the machine. Does anyone even put these back on and if so how much do they cost and is the process easy? I noticed all the stars are gone on my RWB S2000 too from people likely just cleaning the glass. Can we also buy more stars?
Thanks,
Scott
p.s. May have to include pic a little later
-
Scott, I probably have a brand new set of White Ice backlit strips.
Jim
-
Jim, I have been trying to PM you for parts but to no avail. Wondering if you might be on vacation or if not would it be better to call you?
Scott
p.s. I also need the wire connector for BV for white ice as seen in pic I am attaching.... as well as the 15 ballast. Got these?
-
Scott, yes I was on vacation.( Las Vegas) and heading back out again this week. (Caribbean) warm 80 degrees.
I have all your parts, let me know when you want me to send them, from you pm it sounded as if you wanted to wait until you finished your list and then ship it all to save on shipping,
and you can always call, even on vacation and out of the country I will answer.
Jim
-
OMG, so sorry Jim, disregard my last PM I just sent.... dup! Ok, will call you uo to get this thing finalized likely tomorrow..... eer since its 1am later today.
-
Jim, please excuse my delay in getting back to this white ice machine and all. I received the strips that I purchased from you and just now got around to tr and place them in the machine. I noticed that the pre-existing strips all had a different product # to them and the sequence of the bars, cherries and 2x 4x elements are not at all in the same order of each other strips, where as the strips you sent me are all the same product # and in fact none of them even remotely match the order of those found on the older strips. Needless to say, I placed the new strips on the machine, fired 'er up and nothing was in sync at all. Is there a certain spot I must align these new strips to o the wheels or am I SOOL? outta luck? Please advise if anyone else knows a trick on how to align strips on a 3 reel S2000 enhanced White Ice machine. oh, and p.s. I have no sound on the machine even though all sound settings sre correct.q
Thanks!
Scott
-
post a picture of the strips from your machine. are you sure the SB chip is the correct chip in your machine?
Jim
-
get the numbers off the strips in the machine, will check to see if I have those for a 3 reel, nine line game, the strips I sent you were for a single line 3 reel game.
Jim
-
Jim, well that makes a little better sense, but I thought that you asked to see the machine way back b4 I ordered the strips and I posted a pic of the machine for you no? Anyhow, here is the #1 reel on the pic attached below and as you can see its a 92003800 that goes on reel#1.... on reel #2 will be a 92003900 ... and on reel #3 a 92004000. Make sense?
Also, now that I lost my original spot on where the original strips go on the reel how might I re-align them in the correct spots?
Thanks!
Scott
get the numbers off the strips in the machine, will check to see if I have those for a 3 reel, nine line game, the strips I sent you were for a single line 3 reel game.
Jim
-
Scott, no you never did post a picture of the machine, so I thought it was a single line ,3 reel. I'll look tonight to see if I have those strips. as for the alignment, it's pretty simple, each strip has two cutouts on it, one on opposite sides of the strip, the reel basket also has two two plastic position holders the same size as the cutouts positioned on each side of the reel basket, they are not visible as you look at the reel basket, however there is a raised piece of plastic at the spot where these are located, run your finger around the outside of the basket and you will feel that point, then you can look closely and actually see the area where the reel strip fits into. now its just a matter of putting the cutout in the inner basket on both sides and feed it around the reel until you reach the end. takes a little effort to do this but once you get the hang of it , it goes pretty quick. sometimes at the end when the two ends of the strip meet you have to use you finger nail to seat the strip into the track to get it to lay flat, sometimes you have to use double sided tape to accomplish this.
Jim
-
found these strips, the numbers match the numbers you posted, the tag on them identified them as 5 line?? let me know if these match yours. Jim
-
yes sir, those are the ones!!!
How shall we proceed?Scott
found these strips, the numbers match the numbers you posted, the tag on them identified them as 5 line?? let me know if these match yours. Jim
-
Scott, I'll pack them up and ship them out to you! sent you a pm.
Jim