New Life Games LLC
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length

News:

Welcome to the NewLifeGames.com message forum! 

 


NLG Site Navigation Menu


Archives of old posts can be found at...... Newlifegames.net/nlg/

Author Topic: Nintendo Arcade  (Read 27552 times)

0 Members and 1 Guest are viewing this topic.

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Nintendo Arcade
« on: May 04, 2014, 08:08:42 PM »
Model: Mario Bros
Symptom: No sprite graphics

Board would play blind, show text, and floors but had no moving graphics, characters, pipes, or title graphics. The Video EPROMs had no activity on the address or data lines, except A0-A3. Traced it back to the input edge of the Video PC Board. Data was coming into the 74LS245 but not out from it. The enable and direction lines were stuck high. Problem was on the CPU board.

Tracked the signals back to the CPU board: "OBJ WR*", "OBJ RD*", and "OBJ RQ*" were all stuck high. Replaced the 74SL138 at 3B to no effect. Tested the PROM at 5B by substitution even though the signals looked good. All the signals to the 3A, 3B, and 4A chips looked good except for the MREQ* signal. It was pulsing, but not the same as a known working board. This signal came from the Z80A DMA controller at 5D. The "BUS REQ*" and DAI* signals lines between it and the CPU were stuck high. Replaced the DMA Controller IC to repair the board.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #1 on: May 04, 2014, 08:08:54 PM »
Model: Popeye
Symptom: Dead

Replaced bad CPU and cleaned corroded pins on 2 chips on the CPU board. Tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #2 on: May 04, 2014, 08:09:10 PM »
Model: Popeye
Symptom: Dead

Swapped out the Rev 1 EPROMs with Rev 2 EPROMs from a parts board. The EPROMs read good but at least 1 would not work at speed. Replaced a bad AY-3-8910 IC at 7L to fix an audio and I/O problem.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #3 on: May 04, 2014, 08:09:26 PM »
Model: Donkey Kong 3
Symptom: Bad colors, garbage on screen, and screen scrolled.

Repaired broken legs on the horizontal adjustment pot and replaced a cracked vertical adjustment pot to fix the scrolling screen problem.

The video board had a corrosion problem on it. Replaced and socketed the 74LS373 at 3k, the 74LS157 at 3L, the 74LS157 at 3M, the EPROM at 3M, the EPROM at 3P, 74LS174 at 2N, 74S163 at 1N, and the 74LS267 at 1P. Cleaned the corroded pins on the PROM at 2N and replaced the bad socket. Now the video garbage problem was solved.

The bad colors would come and go when the board was tapped or flexed. Replaced a bad socket on the PROM at 1D on the CPU board then tested the game.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #4 on: May 04, 2014, 08:09:38 PM »
Model: Donkey Kong 3
Symptom: Dead. Garbage on screen

The lower 8 address lines and the 8 data lines were garbled. Replaced a bad 74LS374 at 5F, 74LS244 at 7A, and 74LS240 at 2M to fix the problem.

Game would play but was missing some sounds. The RP2A03 at 5J showed no activity. The RP2A03 at 5J, and the EPROM for it at 6H tested good by substitution into another board. Replaced a bad SRAM IC at location 6F to fix the sound.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #5 on: May 04, 2014, 08:09:53 PM »
Model: Donkey Kong
Symptom: Dead, garbage on screen

Replaced the EPROMs at 2A and 2E. Board worked but was missing audio.

Reseated the EPROMS at 3H and 3F to fix most of the audio. The walking sounds were missing. Replace broken capacitor C22 and missing capacitor C26 to fix the walking sounds.

Reseated the EPROMs on the video board to fix a horizontal line issue and played a few games to test.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #6 on: May 04, 2014, 08:10:27 PM »
Model: Eight Ball Action
Symptom: Dead

Board is a conversion for Donkey Kong Jr by Seatongrove Ltd.

1MHz clock is missing. Clock circuit is working fine. Replaced bad board interconnect ribbon cable. Board now had video but no sync. Fixed broken legs on the horizontal and vertical adjustment pots. Tracked sync problem to card edge connector. Cleaned edge connector to repair.

Board now had sync but had garbage on the screen. Reseated the program EPROMs and it booted. Replaced 3 program EPROM sockets and 2 other EPROM sockets on the CPU board to finish the repair.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #7 on: May 04, 2014, 08:10:39 PM »
Model: Donkey Kong Jr.
Symptom: Dead, Garbage on screen.

Replaced an 8035 CPU with the proper Z80A CPU. Game would boot but had garbage on the screen and no sync. Repaired the broken horizontal and vertical adjustment pots to fix the sync issues. Replaced a bad board interconnect cable to fix the garbage problem and tested the game.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #8 on: May 04, 2014, 08:10:51 PM »
Model: Donkey Kong Jr.
Symptom: Low audio

Replaced C13 and C161. Tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #9 on: May 04, 2014, 08:11:04 PM »
Model: Donkey Kong, Jr.
Symptom: Plays the game start sound in a constant loop

Replaced bad 74LS174 at location 3D. Tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #10 on: May 04, 2014, 08:11:16 PM »
Model: Mario Bros
Symptom: Graphic corruption

Replaced bad 74LS283, 74LS244, and 74LS273. The 283 was causing problems with position on the screen and 74LS244 and 273 were causing a data line to be stuck on one of the 2148 RAM chips, causing problems with graphic corruption and position on the screen. Tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #11 on: May 04, 2014, 08:11:29 PM »
Model: Mario Bros
Symptom: Dead. Garbage on screen.

Board was dead. No activity on the Z80 address or data lines. Reset worked and clock was correct. When CPU would come out of reset there were NO pulses on the address or data lines. CPU chip tested fine. Replaced bad Z80A-DMA chip and tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #12 on: May 04, 2014, 08:11:41 PM »
Model: vs. Excitebike
Symptom: Dead

Every EPROM was blank on the board! Reprogrammed 6A through 6D and 8B. Replaced bad EPROM at 8A. Board was dead and D1 was stuck. Replaced bad RAM at 6E and as a precaution, the same Fujitsu RAM at 1E. Tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #13 on: May 04, 2014, 08:11:52 PM »
Model: vs. Super Mario Bros
Symptom: Dead.

Board had a solid greenish brown screen on startup. The RP2A04 IC on the unpopulated side of the board died. Replaced the IC with a simple jumper between pins 30 to 38 in the socket and tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #14 on: May 04, 2014, 08:12:11 PM »
Model: vs. Super Mario Bros
Symptom: Partial garbled graphics and will not recognize any inputs

Repaired bad traces to the enable pins on 7P, 8P, 8M and 8N to fix inputs. Patched bad trace on data line D1 between the ROMs at 8A and 8B. Tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #15 on: September 13, 2014, 07:20:01 PM »
Model: Mario Bros
Symptom: Missing graphics, corruption on screen

Board worked, but had no moving graphics and displayed text ont he top quarter of the screen. Replaced bad Z80A-DMA chip and tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #16 on: November 08, 2014, 08:42:09 PM »
Model: Super Punch Out
Symptom: Poor colors and corrupt display on upper monitor.

The upper monitor was missing blue and would repeat the left most part of the screen across the entire screen several times.

Replaced bad PROM in the output circuit to fix the color issue and replaced a bad 74LS161 to fix the graphics issue. Tested.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #17 on: November 13, 2014, 11:10:53 PM »
Model: Punch Out
Symptom: Dirty, missing parts.

Cleaned CPU board. Replaced missing CPU and missing 6264 SRAM IC chip. Fabricated 1 new ribbon cables for the board and installed them. Board would not boot. Replaced bad program ROM and tested. Board would boot and try to play but was missing players. Replaced 2 74LS163 chips with rusted and tarnished legs that weren't making good contact with their sockets and 2 bad 74LS163 chips on the video board. Tested. Replaced missing hardware and retested
« Last Edit: November 14, 2014, 12:04:45 AM by channelmaniac »
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #18 on: November 13, 2014, 11:12:41 PM »
Model: Punch Out

Replaced CPU, 2 corrosion damaged 74LS240 ICs, 1 corrosion damaged DIP switch, fabricated 2 new ribbon cables, and tested. Board had scrambled images on the screen. Replaced 4 bad 2564 EPROMs on the BAK board and 1 74LS161 IC. Tested. Fabricated replacements for 2 of the board fasteners and retested.
« Last Edit: November 14, 2014, 12:05:13 AM by channelmaniac »
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

Offline channelmaniac

  • Surface mount soldering geek
  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2472
  • Reputation Power: 174
  • channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!channelmaniac Is an-NLG GOD!
  • Few things are better than fixing an old game...
    • Arcadecomponents.com - Looking for hard to find chips?
Re: Nintendo Arcade
« Reply #19 on: November 13, 2014, 11:17:37 PM »
Note: Punch Out Revisions and ROMs

When repairing Punch Out and Super Punch Out boards it's important to note there are 2 different ROM types that could be on the boards: 2763 or 2564. These chips are NOT interchangeable and the code they use is not interchangeable.

If you use the wrong code on the 2564 chips you will have incorrect colors and scrambled graphics on the screen.

Also the PROMs on the video output come in 2 different types and are distinguished by their labels: Pink or white. The Pink labels are known for fading so you may have to read a good PROM's contents to verify which type you are dealing with on the board when replacing a bad video output PROM.

If the boards are working I've been able to swap a -01 CPU board onto a -02 Video and -02 BAK boardset; a -02 CPU board onto a -02 Video and -01 BAK; and a -01 CPU onto a 02-Video and -01 BAK with no apparent issues.
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com

 

Cell Phone and Pad Mode

imode wap wap2

NLG Archives

Archives @ newlifegames.net Wayback Machine

Contact Us

NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442
If you find this site helpful, please consider becoming a Contributing NLG Member with a monthly subscription to help cover the cost of pizza, coffee, aspirin, hosting, and bandwidth.
Contributing Members: get unlimited personal messages, can save topics and replies as drafts,
can post to the Classified ads, get unlimited access to the downloads, and also get this minty badge:



**Subscription Link** (Click Here) **Subscription Link**



           
If you would rather remain anonymous Thank You or just want to help support the site, please use this "make a donation" button:




From your entire NLG staff, thank you for supporting NLG.


New Life Games LLC 1788 HIGHWAY 95 UNIT 30 BULLHEAD CITY AZ 86442




Newlifegames.com     Newlifegames.net     Newlifegames.org

Newlifegame.com     Newlifegame.net     Newlifegame.org    Newlifegames.us

   New Life Games     NewLifeGames  NLG

 We Bring new Life to old Games    1-888-NLG-SLOTS

Are all Copyright and Trademarks of New Life Games LLC 1992 - 2022


FAIR USE NOTICE:



This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml
If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.




The NewLifeGames.com website is optimized for use with Firefox and a minimum screen resolution of 1600 x 900 pixels.

SimplePortal 2.3.5 © 2008-2012, SimplePortal