New Life Games LLC

NLG Classified ads and White Sheet => NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! => Topic started by: 69sixpackbee on September 25, 2016, 09:42:44 AM

Title: Power Connector Harness For Backlit Control Board Needed
Post by: 69sixpackbee on September 25, 2016, 09:42:44 AM: Hi guys!
I have a very early vision ready S2000 upright that does not have the small 6-pin Molex connector for the backlit control board from the power supply. That is the one that is usually present in the loom but just zip tied out of the way. I have my controller and reels in and running but now I just need to power up the control board.
If anyone has one of these harnesses in their stash please hit me up!

Thanx,
Bud
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: ALIDMAN on September 25, 2016, 07:14:57 PM: I have couple of donor machines , if I can see picture of what you want I will check if I have it
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: 69sixpackbee on September 25, 2016, 10:29:59 PM: Cool!
The missing connector goes into the empty socket in the pic.
I believe it is a short harness that runs from the power supply and up to near the pull handle mechanism and, if not used for the backlit reels, is usually zip tied to the wires that run along the rear of the machine AFAIK.
Thanx!
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: ALIDMAN on September 25, 2016, 10:52:20 PM: I need to see the panel ,
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: 69sixpackbee on September 25, 2016, 10:59:28 PM: No prob. I'll get more pix tomorrow.
Thanx!
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: 69sixpackbee on September 26, 2016, 08:42:28 AM: More to follow.
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: 69sixpackbee on September 26, 2016, 08:44:49 AM: Few more...
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: 69sixpackbee on September 26, 2016, 08:47:00 AM: One more...
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: Ken on September 26, 2016, 08:48:41 AM: I think on the old vision machines you have to run the power from the mother board if the 6 pin power connector is not just below the right side of the power supply.
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: 69sixpackbee on September 26, 2016, 04:55:01 PM: Yup. I found the info in the archives..
http://newlifegames.net/nlg/index.php?topic=5055.0 (http://newlifegames.net/nlg/index.php?topic=5055.0)
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: ALIDMAN on September 28, 2016, 10:55:11 PM: so did you fix it or still need the cable , I know which cable you are talking about now , let me know
Title: Re: Power Connector Harness For Backlit Control Board Needed
Post by: 69sixpackbee on September 29, 2016, 08:35:43 AM: Yep..I got it connected. I cut a 4-pin Molex harness from an old power supply from a junk mid-tower PC I had in the garage and just tapped into the wires going down to the mother board. Works like a champ!

Thanx