**Video Poker, Keno, Slots, 21** Gaming machines > BALLY Game Maker |
Gamemaker Game Change |
(1/1) |
Tacman:
Topic: Bally Game Maker clear chip problem bob35614 Bally Game Maker clear chip problem « on: April 18, 2007, 05:06:11 PM » -------------------------------------------------------------------------------- I have been trying to add a couple new games to our machine. I bought a clear chip and installed it in P-10 and set dips 7-8 to on . I restart machine and saferam clear enabled comes on screen. I then use key to reset and it says saferam is being erased, reset dip switches and restart. Then I do the hardware calibration, then software calibration. Then the screen comes up to pick denomination which I do. Then I hit save and hit exit and it says no games are available for play with GAME DISABLED inside a box. I can get no farther than this screen. When do I take out the clear chip? For something that sounded so easy to do it has been a real pain. Can anyone advise what is wrong? Also where can I download a manual for this? Please help before the wife gets crazy that her machine is down. Thanks midas Re: Bally Game Maker clear chip problem « Reply #1 on: April 18, 2007, 05:52:02 PM » -------------------------------------------------------------------------------- So far, so good. At this point, TURN THE RESET KEY WITH THE DOOR OPEN. Select the option, TURN ON/OFF Game. Now select the games to turn on. hit exit. and you're all set!!!! midas Re: Bally Game Maker clear chip problem « Reply #2 on: April 18, 2007, 05:54:22 PM » -------------------------------------------------------------------------------- one more thing, you remove the clear chip when you remove the processor to reset the dip switches. I've attached some instructions. bob35614 Re: Bally Game Maker clear chip problem « Reply #3 on: April 18, 2007, 06:08:36 PM » -------------------------------------------------------------------------------- Thanks for reply. When I go to the turn on game option it says no game in every box. Its like none are installed. What happened to them? midas Re: Bally Game Maker clear chip problem « Reply #4 on: April 18, 2007, 06:49:39 PM » -------------------------------------------------------------------------------- Bob, are you sure the chips are installed properly with the notch on chip facing notch on socket with the shorter chips installed with the notch 2 pins lower than the socket notch. What games are you trying to put in? and what version is your mains? bob35614 Re: Bally Game Maker clear chip problem « Reply #5 on: April 19, 2007, 02:40:03 AM » -------------------------------------------------------------------------------- Yes putting them in notch to notch , short ones 2 pins from notch. Putting in bonus poker and double double bonus. Where can I find the version at and will let you know. thanks bob35614 Re: Bally Game Maker clear chip problem « Reply #6 on: April 19, 2007, 02:55:58 AM » -------------------------------------------------------------------------------- Midas, I see a v7000 on the board. midas Re: Bally Game Maker clear chip problem « Reply #7 on: April 19, 2007, 07:11:32 AM » -------------------------------------------------------------------------------- The games you are trying to install require no special mains. The only other thing it could be is the jumpers on the board. make sure the 4 jumpers next to P1, P2, and P3 are set as follows: w27 - closed w30 - closed w31 - closed w34 - closed if any of the are open, then it prevents you from adding new games. idesign Re: Bally Game Maker clear chip problem « Reply #8 on: April 19, 2007, 08:09:32 AM » -------------------------------------------------------------------------------- He didn't say which mains he has but some of the older ones were on 2 meg chips so they may not be compatible. However, it sound like he has some bad chips. Cactusjack Re: Bally Game Maker clear chip problem « Reply #9 on: April 19, 2007, 11:17:26 AM » -------------------------------------------------------------------------------- Sounds like the game use to work until they put the two games in. They should try removing the two games to see if one of those EPROMs is loading down the data bus. CJ bob35614 Re: Bally Game Maker clear chip problem « Reply #10 on: April 19, 2007, 12:59:24 PM » -------------------------------------------------------------------------------- It did work before for sure. Does anyone have a picture of the board you could post that shows how the chips go? My brother messed with it before I got to it and he may have pulled chips and put them in wrong. A picture or a schematic would show me exactly the way they go. Thanks for all the replies, this is a great site. midas Re: Bally Game Maker clear chip problem « Reply #11 on: April 19, 2007, 01:13:25 PM » -------------------------------------------------------------------------------- Attached is instructions with pictures. -------------------------------------------------------------------------------- tacman |
Navigation |
Message Index |
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |