Bill Validators, Currency Acceptors and Printers => MEI Mars Bill Validators => Topic started by: shortrackskater on March 13, 2023, 04:35:29 PM
Title: CASH CAN NO LONGER BEING RECOGNIZED?? IT MIGHT NEED A GOOD CLEANING.
Post by: shortrackskater on March 13, 2023, 04:35:29 PM
(This subject started off as a issue with my BV not being recognized, by my machine, an IGT S2000 with an MEI bill validator. It ended up being my interface or I/O card. So, I'm now editing the information from all the experts into a thread on cleaning your BV box.)
Read through this thread if your machine no longer recognized the cash can. First, check your I/O card just to rule it out. Endure the contacts are clean, etc. From my understanding, if it is the I/O card, the machine will not even recognize that there's a BV installed. But it can't hurt to check.
Title: Re: CASH CAN NO LONGER BEING RECOGNIZED?? IT MIGHT NEED A GOOD CLEANING.
Post by: Stayouttadabunker on March 13, 2023, 05:19:46 PM
There's a prism "triangle pole" in the bottom of your cashbox....it could be dusty. That prism "triangle pole" is hard to get to....it's located in the very bottom, middle of the box on the end of the molded, clear plastic stacker arm itself. The plastic optics on both sides of the prism "pole triangle" run to the outside of the box. Those optical lens need to be clear of dust as well because there's sensors on the bottom of the MEI head that's inline with them. The head senses that there's an inserted box when light goes thru it. Blow the dust off the prism "pole"with a compressed air can that has the long tube or throw your cash box in the dishwasher.
When you clean everything and push the cashbox back in, you should get a slow, single green blink on the head LEDs. When the door is closed, that slow green blink should be solid green and the yellow validator light should come on
Title: Re: CASH CAN NO LONGER BEING RECOGNIZED?? IT MIGHT NEED A GOOD CLEANING.
Post by: RB on March 13, 2023, 07:50:10 PM
You can remove those plastic optics from the stacker and wash them with some mild dish soap and water. Works wonders.
Title: Re: CASH CAN NO LONGER BEING RECOGNIZED?? IT MIGHT NEED A GOOD CLEANING.
Post by: Stayouttadabunker on March 14, 2023, 04:44:05 AM
The plastics usually have two Philips screws...easy enough to remove with a screwdriver, but some of mine have what looks like ....rivets? I haven't been able to get those ones apart. For those ones, I stick the tube of the compressed air in where the "pole triangle" is near the gears and blast the dust off of it.
Title: Re: CASH CAN NO LONGER BEING RECOGNIZED?? IT MIGHT NEED A GOOD CLEANING.
Post by: hotlsot on March 14, 2023, 09:21:41 AM
If you have the cash can with the rivets take the whole thing to the sink and run water through it, no soap, just water. give it 24 hours to dry and that should take care of it.
Title: Re: CASH CAN NO LONGER BEING RECOGNIZED?? IT MIGHT NEED A GOOD CLEANING.
Post by: Jim on March 14, 2023, 02:12:50 PM
This is for those people who Mei Cash Boxes with the rivets that secure the stacker.
three items have to be cleaned in the cash box, the two plastic pieces, and the plastic tip that sits in the center of those two plastic pieces. the two pieces can be removed from the case, just use a small screwdriver or something that will push them out of there location, wash with windex or ? dry and return to their position, easier if you remove the yellow stacker and spring. then extend the pusher part on the stacker to expose the plastic tip, clean this .now reassemble and test , this will cure 98% of bad boxes, after you do a couple it only takes 10 minutes to do.
to remove the rivets on the older boxes that do not have screws, drill a 1/4 hole in the plastic even with rivet, then put a small flat blade screwdriver into the drilled hole and get the blade under the rivet, and pop it out, then when you reinstall secure with a sheet metal screw the size of the hole of the rivet.
Hope this helps
Jim
Title: Re: CASH CAN NO LONGER BEING RECOGNIZED?? IT MIGHT NEED A GOOD CLEANING.
Post by: Stayouttadabunker on March 14, 2023, 05:54:22 PM
I drilled two 1/4" holes thru the cashbox, and I could NOT work the rivets out with a flatheaded screwdriver....believe me, I tried. :rotfl: So I grabbed a center-punch, and drilled down about an 1/8" into the top of the rivet head. With the round "volcano"present, I punched a reverse screwdriver to make some indentations on the "crater's" edge. I found a small Torx bit, and slowly reversed the head, until it came out.
Here's a little video I made of the 2nd rivet I did...>>>