New Life Games LLC
Progressive Controllers and Displays => Mikohn Progressive Systems => Topic started by: Nurbo on October 06, 2019, 11:41:41 AM
-
Hello,
I have a problem with the progressive display on my Bally S6000 Blazing 7.
When I start the machine, the Mikohn turns on and starts its initialization phase, the display is normal.
Meanwhile, the S6000 starts, and displays 91-0 on the screen.
At the end of the progressive start sequence, the error code 91-0 disappears and you can play normally. The amount of the progressive increases normally, BUT, the display is as stagger ... ???
To return to the normal display, remove the top glass, switch the Mikohn switch to MENU (ADDR, SYST, DISP), then put it back on the GAMES position.
And there the display becomes normal again.
Strange behaviour ? Do you have an idea of what is causing this problem?
https://youtu.be/Mngr1PVTGJ4 (https://youtu.be/Mngr1PVTGJ4)
http://youtu.be/Mngr1PVTGJ4 (http://youtu.be/Mngr1PVTGJ4)
-
Solved !
Change option 02 to 5 instead of 4 and change option 78Lo to 5 instead of 4 :applause:
-
:hissyfit: :hissyfit: :hissyfit: :bawling: :bawling: :bawling:
Not solved.....
After modifying the options said below, the error code 91-0 gone away, but the display stay mismatch on boot...
-
Hello,
It was a bad Mikohn Progressive parameters...
I change F4 parameters in Jackpot Programming Menu and it's done !
F3 = SNGL
F4 = M-04 (instead of M-00 before)
F5 = 3sec
F6 = JP0
F7 = $$$$
F8 = MS08
Moderator/Admin : Perhaps to put my thread in Mikohn Progressive Systems ???
-
Thank You for the follow up. !!
-
If you look at setting progressive set up for Bally 6000 it shows F4 being set to M-08 not M-00 or M-04
Yours is working on M-04 any way to check it using 08?
Did you use this link to set up your machine?
http://newlifegames.com/nlg/index.php?topic=901.0 (http://newlifegames.com/nlg/index.php?topic=901.0)
If M-04 works I could add a note M-04 or M-08 on that thread
Rich
-
Hello,
Yes I used the post that you quote but I adapted according to my tests.
I will try again on the options chosen and I will retest with F4 = M-08 but it does not work it seems to me.
I also found that in the documentation PSP v2.
-
Hello,
It was a bad Mikohn Progressive parameters...
I change F4 parameters in Jackpot Programming Menu and it's done !
F3 = SNGL
F4 = M-04 (instead of M-00 before)
F5 = 3sec
F6 = JP0
F7 = $$$$
F8 = MS08
With this Mikohn setup, I use this 11d settings (coin, no printer, BV installed but unplugged):
9 = 6
2 = 5
7 = 1
56 = 800
51 = 800
58 = 800
78lo = 1
73 = 3
61 = 1
81 = 1
80 = 0
-
If you look at setting progressive set up for Bally 6000 it shows F4 being set to M-08 not M-00 or M-04
Yours is working on M-04 any way to check it using 08?
Did you use this link to set up your machine?
[url]http://newlifegames.com/nlg/index.php?topic=901.0[/url] ([url]http://newlifegames.com/nlg/index.php?topic=901.0[/url])
If M-04 works I could add a note M-04 or M-08 on that thread
Rich
Hello Rich,
Both settings works.
F4 = M-04
F8 = MS08
or
F4 = M-08
F8 = MS00
Attached 2 PDF files with settings for Bally and Mikohn