| **Reel Slots** Gaming Machines > IGT S and S-plus Reel Games |
| IGT S+ power supply not supplying power to motherboard |
| (1/2) > >> |
| Flappa:
I recently bought a IGT S+, Double 10 Times Pay, slot machine. When cmos chip is removed for 30 seconds and put back in and machine turned on It gives me the 61 error code. A "0" flashes for a second in the coins played window. When I push the white reset button, the code changes to 61 - 1 and it bings once. The BV does nothing and the machine does not recognize door open or closed. Used Volt meter to check voltage at motherboard Molex and there was none. Then I unplugged the other end that goes into the power supply and with machine on checked voltage there and also was none. I'm thinking my power supply is no good, but wanted to run it by the group for assistance. The 3 fuses are the correct amps and good. If the consensus is that I need a new power supply. Can anyone point me in the right direction? TIA |
| Flappa:
I tried to add some pics, but even one pic is too large a file. |
| Stayouttadabunker:
Don't worry about the BV yet....you must first get rid of the [61-1] When you get to the [61-1], close the door, and turn the Jkpt/Reset key once. Tell us what happens next. As far as checking for voltages, you must tell us EXACTLY where you are putting the red and the black probes of you multimeter. You must have voltage going to the motherboard, or your display would not be showing a [61-1]. To check the door emitter, turn on the power switch, and view the emitter with a digital camera. You should see a blue-ish light flickering out of it. To check the cabinet receiver optic, disconnect the 2-pin harness, put a multimeter on ohms, and read the two pins in the optic connector by shining a flashlight on and off of the receiving optic...the numbers on the multimeter will change if it's good. |
| Flappa:
Ok. After removing and replacing the cmos chip it will go from the 61 to 61-1 only once Until I remove and replace the chip again. All other times I turn on the machine and get the 61. Press the reset button, nothing happens. No click or anything. The lower candle light is flashing fast upper light, not on. When I power up the machine, the reels lock but they never spin during start up. After closing the door and turning the reset key the winner paid shows 76 credits shows 77 and 0 and 1 flashing in coins played. Each turn off the keys brings up different numbers, but the coins played numbers are in sequence up to 9. Then it goes back to 61 and will repeat that forever. On the motherboard Molex I took my Volt meter black lead and put it on the farthest right green wire. And then tested all the other wires 0 V. Then I put the black lead on the other green wire and touched all the other wires and again 0 V. I did the same at the power supply and again 0 V everywhere. I figured that I couldn't get out of the 61 error code situation at least because it couldn't tell if the door was shut. So I wired the optics wires to a switch. |
| Stayouttadabunker:
Try wiggling the that white power Molex on the motherboard slightly upwards, while watching the reel baskets for movement. They should get "stiff". When you say "0 V"...do you mean AC or DC? Your multimeter should be set to VAC when checking. Pull the plug off of the power supply and check the power supply plug on the box. I'm only guessing you have the power supply box on the right-hand side of the cabinet uder the bill acceptor box? Or is yours the older cabinet with the power transformer in the rear of the cabinet? Look at this drawing I've attached to this Reply...>>> |
| Navigation |
| Message Index |
| Next page |
|
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |