New Life Games LLC
**Video Poker, Keno, Slots, 21** Gaming machines => IGT PE and PE Plus Poker Games => Topic started by: keithcorcoran on September 03, 2023, 07:13:33 PM
-
Just picked up this DROP IN today for free. It has "Multi Poker" come up on the screen that comes up after doing the following...
Doesn't seem to be any serial number plates or any stickers on it denoting the model.
I did find this which looks like a parts list... but not other manual.
https://rwatts.cdyn.com/download/PEPLUS/MECHANILAL%20PARTS%20PLAYERS%20EDGE%20PLUS%20%20FLAT%20TOP.pdf
When I power on I get
VERIFYING GAME MEMORY - PLEASE WAIT
Then goes to
DOOR OPEN
CALL ATTENDANT
CMOS DATA
I can hold the self test button and get a chime.
If I turn the reset key I get to see the Multi Poker screen with
STATISTICAL METERS
I'm assuming I'm missing half of my top door optic switch because I have what looks like a metal plate with 2 screw holes in it and a black and red wire that looks like it was cut just about long enough to reach that mounting point (which aligns with the optic on the bottom.
On the bottom case I have the other half of the switch with a wire that runs along the front. That was disconnected.
I assume there's another switch on the front door but that looks like it is just maybe a magnetic switch mounted to a bracket with nothing on the door that comes off.
How can I find a replacement switch to see if that fixes this?
Would like to try to get it running before just scaveging it for the 13" monitor for one of my arcade machines.
Thanks
-
The belly door has a small door optic also.
Find the machine side 4 pin female connector and jumper pin 1 to 2 and pin 3 to 4.
It should be found right side center of the belly door frame.
-
Well ok. that was easy enough once I got the polarity right on the lid (top) switch.
Now I need to figure out how to adjust the coin slot so quarters fit in. Seems they don't fit unless I slide the black plastic part attached to the spring on the coin mech to the right a little (with the sticker that says "slide to replace coin")
I thought maybe the little thumb screw on there might do it but maybe i need to slide it to the right size and then tighten the set screw next to it.
Odd part is if i do that, it'll also take nickels as well as quarters.
OK.. it occurred to me why it's called a 'coin comparitor' haha
Slide the black thing to the right... stick a quarter in there... now it only takes quarters.
Stick a nickel in there, now it only takes nickels.
DUH.
NOW...
I think now I'm going to have to go get a couple hundred in quarters to fill this thing and clear the HOPPER EMPTY error... then figure out how to make everything HAND PAY.
(Also, is there any way to empty the chute from the hopper without taking everything apart?)
-
If you're referring to the metal guide from the hopper that brings the coins up to the payout bin, that's called the hopper escalator.
Note that the hopper and escalator are designed for one specific size of coin and will not work with any other size of coin. If you have a quarter hopper and escalator, it needs quarters and it will not work with nickels.
You do not need a couple hundred dollars in quarters in there. You could run it with as few as about 20-30 quarters in there, although more would be fine. Can you see how many credits it's trying to pay out? You can always have it pay out like a hundred or so at a time and then just keep recycling the coins back into the hopper until it has finished its payout.
-
I was able to dig up about $15 in coins form the wife's piggy bank. :)
Payout was about 427 coins so it took a little bit but I got it reset.
It's been working well since. Probably looking to sell it now but was thinkign of maybe wrapping it in some wood grain vinyl or covering it in some wood grain panelling since it's a drop in model that someone build a dolly-like base with wheels for.