New Life Games LLC

**Reel Slots** Gaming Machines => SIGMA Reel Games => Topic started by: LuxuriousBastard on March 02, 2022, 11:08:35 AM

Title: Replaced Board Sigma SG-300 still Have issues
Post by: LuxuriousBastard on March 02, 2022, 11:08:35 AM

Here is a video of the issue. Rom Clear maybe?
https://youtu.be/0WlOTYhhO6U (https://youtu.be/0WlOTYhhO6U)

Title: Re: Game Data Mismatch after replacing with new board
Post by: Mr. Dinoman on March 04, 2022, 08:33:33 AM

Hello,
You should just be able to turn the reset key twice with door closed to get past the miss match error...Also it look like you did not transfer the GALchip (the little one about the GAME erpoms...
Resetting and clearing ram on a Sigma

Hold in the test button next to the power switch, then turn and hold the reset key, then turn on the power switch at the same time. Continue holding the test button and the reset switch until the reels turn and the door says ram cleared (about 15 seconds). The door should read turn reset key twice. This will hard clear the machine

Must have GAL01 or GAL03 denomination chips  (Not GAL02)

Title: Re: Game Data Mismatch after replacing with new board
Post by: LuxuriousBastard on March 04, 2022, 10:04:13 AM

Ill look at it again when I get home...But i'm pretty sure I transferred all the chips over to the new board. Turning the reset key does nothing. as well as holding the test button and reset key when powering on the unit.

Title: Re: Game Data Mismatch after replacing with new board
Post by: LuxuriousBastard on March 06, 2022, 02:41:18 PM

Okay.... Update.
Turns out I did forget to swap over one chip (Small Gal Chip)
Powered on the machine.
Rom Error
Cleared error.
Now Im back to game play. However, the new mother board did not fix previous issues.
I can play the machine using quarters. But it still won't pay out if I hit the payout button.
Also the bill validator still does not work.

Please advise what do do next

Title: Re: Game Data Mismatch after replacing with new board
Post by: Mr. Dinoman on March 09, 2022, 11:22:46 AM

check all the wiring from the payout switch...Make sure all connectors are in there correct possition...Does the bill validator cycle at startup?...Maybe post a video of your machine powering up...
Jimmy

Title: Re: Game Data Mismatch after replacing with new board
Post by: LuxuriousBastard on March 09, 2022, 12:09:33 PM

I did check all the connections at the payout switch. As well as bench tested the hopper. (works)
The bill Validator does not cycle on power up. Ill post a video tonight.

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: Mr. Dinoman on March 09, 2022, 12:51:08 PM

If the BV does not cycle on power up then you might have a bad power supply...check for voltage at the BV...

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: LuxuriousBastard on March 09, 2022, 01:15:04 PM

what is the voltage there? 12V or 24V

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: Mr. Dinoman on March 09, 2022, 01:39:32 PM

What BV do you have?

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: LuxuriousBastard on March 09, 2022, 02:25:05 PM

Im at my office so I will check when I get home

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: LuxuriousBastard on March 09, 2022, 10:02:42 PM

 https://youtu.be/aS6wup1fN1M (https://youtu.be/aS6wup1fN1M)
 https://youtu.be/z5fkZ8gvj8M (https://youtu.be/z5fkZ8gvj8M)
 https://youtu.be/63lBiGtAb2Q (https://youtu.be/63lBiGtAb2Q)

Here are a few more video clips of the machine

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: Mr. Dinoman on March 10, 2022, 09:01:34 AM

Looks like you have the BV cable plug into cn19...It is supposed to be in cn18...
Try that and see if BV cycles...

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: Mr. Dinoman on March 10, 2022, 09:03:05 AM

Also check and verify you have 5vdc 12vdc and 24vdc at the board test points...

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: LuxuriousBastard on March 10, 2022, 01:12:07 PM

Thank you! I will check those when I get home.

Title: Re: Replaced Board Sigma SG-300 still Have issues
Post by: LuxuriousBastard on March 10, 2022, 08:25:39 PM

So i moved the Bill Val Cable...and still no go. I did a rom reset and still no change....Also wonder why I can't get into the menu.