New Life Games LLC
**Video Poker, Keno, Slots, 21** Gaming machines => SIGMA Video Games => Topic started by: SummitTrouble on October 15, 2019, 02:57:59 AM
-
I have a Sigma Joker Poker game that is stuck in the test mode (the center card says TEST). This started by a hopper tilt, when someone hit the COLLECT/PAYOUT button and there weren't enough coins in the hopper to make the payout. I managed to get the game playing again, but in the test mode. I don't have a manual and I can't clear the machine out of the test mode. It's a 1 to 10 coin game, it accepts the quarters, registers the credits, plays and awards credits for winning hands. The payout light is off and you can't collect on the credits, won't payout. How do I get the game out of the TEST mode? I have tried everything. Any help will be greatly appreciated. Thanks, Carl It's a I-2211 model I found on the tag.
-
typically on SIGMA machines you have to reset a tilt using the first key switch on the right hand side of the machine, it is a barrel key, not the same one you would use for the door lock. turning it should reset the hopper empty tilt.
try this and see what happens.
Jim
-
I have tried that, there are three barrel locks there on the upper side right, I have reset it, but I will try again with door closed this time.
Tried the reset switch again, nothing, still has "test" in the center card. It plays, just no payout lit button. I'll take a picture of it. Maybe do a short video. I hurt my back again, and moving slow today. I'll do pic and video as soon as I can this week. Sure would like to get this fixed, so it's back to 100%.
-
On my SG-50B the door switch has a white plastic plunger. If I pull it out while the door is open, it acts as if the door is closed. That will allow you to run the machine with the "Guts" of the machine accessible.
Not sure which of the poker machines you have but I did find this print. It might help fix your problem. I also found a you tube 22 minute video on a Sigma Poker Machine. I did not watch it all to see if they opened it up or if it would be of any value to you.
Going to try and post a PDF of what might be your machine. Not sure what model your's is, but this is a SG-112B. "B" meaning that you have a DBV for paper money...
-
Check for any wires that might have come off on your Barrel switches to reset the game. Check to make sure all the plugs and connetors on the CPU board are in place and secure. You could check your power supply's above the CPU board for the correct voltage. you might have one or two power supply's on your machine. One is for 12volts and if you have two the other one would be 5volts. if you have a multimeter check the voltage output on each one. You can adjust the voltage output by turning the white knob to the right on the power supply. If you only have one power supply then it would be both 12v and 5v. Also you want to make sure the hopper is making contact with the plug, making sure it is all the way pushed in. Make sure that all the connectors on the distritution P.C.B board on the door are secure and check all the wire to the game buttons that they are secure also.
-
is there any change when you push in the cherry switch plunger? that should indicate to the cpu that the door has been closed and the game is now in the play mode. likewise if you pull the plunger out, it should also indicate the door closed and be in the play mode.
did you do anything else to the machine to try and clear?
JIm
-
Hi Jim, no, I just tried the reset switch, I believe it cleared back when the tilt occurred. But since then it has been stuck in this "Test" mode. I'll get a picture or short video. I know it has to be something fairly simple, I'm just missing it. I'll remove hopper, spin it some, and push back in game, make sure it's seated. Thanks again, Jim, will get that pic or video soon, Regards, Carl
-
here is a picture of the "TEST" mode in center card on monitor, I tried clearing with reset switch, I though maybe switch was bad so I jumped the two wires, same thing, didn't help. Has got to be something simple I am over looking! I have tried the cherry switch in and out, doesn't clear "Test" mode. I have checked all the door wiring, everything looks good, there was that one wire disconnected by main power switch, I connected to the spade there, didn't do anything, I think that wire was disconnected when I got the machine. What does the manual say about clearing "Test" mode? The video wouldn't upload, file to large, even for short video.
-
Have you tried to push the test button again? then turning the Last barrel switch, should be marked (LAST) a couple of times.By turning the switch 3 times will bring you back to the start of the game.
-
we are talking about two switches, the reset (barrel switch on the side of the machine) and the door open/close switch (located inside the machine) usually when the door switch is activated in any direction it will trigger an alarm, usually a bell sounding noise to indicate that the door has been opened or closed, do you hear the alarm?
as a last chance effort to get the game running (provided there is not a switch miswired) I have changed a dip switch setting, this will usually generate a promt on the screen to turn the rest switch to acknowledge the change, when you do this, remember what dip switch you changed and then return it to its original position.
there are usually two sets of dip switches on the board, hopefully they are not hard wired on the bottom side of the board.
sounds like there is a switch wired in the door open mode ??
Jim
-
The reset switch is on the outer cabinet, top right, I tried that; the other switch is the door switch on the inside, top left. Yes the machine does give it's beeping alarm each time the door is opened, and when you initially turn on the game. That works fine. Also, I noticed a "Door-D" on the lower right side of monitor. See pics. The machine runs as it should, it plays, pays credits, play with coins or credits won, just doesn't payout and the test message in the center card. see pics below. What does Door-D mean?
-
Door-D is the cabinet drop door closed.
When the lettering is red it a past error that has cleared and the display will clear after a game is played.
When the lettering is blue the condition is current and has not cleared.
-
Door-D means that the Drop door is/was open. You might want to check and see if there is a Cherry switch on the bottom of the machine or a couple of wires just hanging down below that had a jumper connected to them that fell off. The drop door was for the overflow of coins from the hopper and sent them to a can down in the cabinet.
-
Maybe this will help.
-
Thank-you! That does help, it explains why the TEST mode occurs. Now, how do you clear that test mode? Are there more instructions to that sheet you posted to clear the test mode? The procedure to clear TEST mode? What is the drop door, and where is it located? I understand what the machine door is, but not the drop door. It appears the drop door must be closed for TEST mode to be cleared?
I figured out what the drop door is, I think, that coin divert that allows the coins to drop down the chute to a coin box under the cabinet? Instead of going in the hopper? when machine is turned on, the drop door closes so coins go to hopper. when that door is open, coins got to drop box. Bit what is next step to clear TEST mode?
-
Try procedure 2 and see if that clear's the Door-D issue. Don't know if you have two keys for your machine or not. But if you don,t I would jumper the meter switch and use your key for the reset switch. Just follow the instructions for procedure #2.
-
I will try that, I do have 2 keys to the machine. #2 doesn't really say anything, do you have the next page in the manual? Is there a #5 instruction?
-
Did I forget to upload the image. If I forgot here it is.
-
I just have 1 key for reset, meter, and last game switches, so I'll jump the rest switch, turn on the meter switch, turn the power on and un-jump the reset switch, hopefully that will clear the test mode. I'll let you know, Can you email me that manual? If you have downloaded?
-
OK, I fixed it, I did above procedure, it cleared out everything. The trouble was the purple wire above main power switch got pulled of it's blade connector, so I slipped it back on the middle blade on the connector, and it eliminated that "Test" mode, the M-Door and Door-D message was eliminated from lower right screen, after I won a some credits, the payout light lit after Game Over. So it's running 100% again! That wire is associated with the coin door. When you open the coin door, you get that beeping alarm noise, and the 'TEST" lights up on the center car. When you close the door, the "TEST" message goes away, and after playing 1 game, the Door-D and M-Door messages also go away. Thanks for the help and direction to fix it.
-
Glad you got it going :applause: .If you found this site helpful please consider a donation to keep this site up and running.This site has helped me a number of times to get my machine going also. I donate when I can. Even if it is a small amount.So maybe in the near furture you have a little extra money think of this site.