New Life Games LLC

Bill Validators, Currency Acceptors and Printers => JCM WBA 10, 11, 12, 13, 14, 20, 21, 22, and 23 Bill Validators => Topic started by: buybestslots on May 18, 2015, 10:22:01 AM

Title: uba for aristocrat
Post by: buybestslots on May 18, 2015, 10:22:01 AM

have some aristocrats   most have eprom on uba some don't  is there a file to flash ones with  eprom to us money   for aristocrats? some are uba 10 / some 11
thanks
steve

Title: Re: uba for aristocrat
Post by: buybestslots on May 20, 2015, 05:21:32 PM

bump will a uba10 id 03 work in a mk6 

Title: Re: uba for aristocrat
Post by: CVslots on May 20, 2015, 05:25:40 PM

ID003 works on Aristocrats. I just got some machines with them.

Title: Re: uba for aristocrat
Post by: buybestslots on May 20, 2015, 05:39:15 PM

they came in with uba 11 with eprom  changed  uba 10 were flashed to id 03     should be right   yes?

Title: Re: uba for aristocrat
Post by: CVslots on May 20, 2015, 08:09:51 PM

Yes, should be right.

Title: Re: uba for aristocrat
Post by: buybestslots on May 21, 2015, 05:20:52 AM

Thanks

Title: Re: uba for aristocrat
Post by: buybestslots on May 24, 2015, 06:33:21 PM

takes and rejects bill  but in test it show the  right bill inserted   I think  my id 03 is wrong   I think we need v1.71-16...

Title: Re: uba for aristocrat
Post by: Harp on May 25, 2015, 02:55:22 AM

Couple of things to check for on Aristocrat Games

ID003 is the correct firmware, V1.71-16 is very old (2008) the current firmware is V2.71-51 but either will do
In your Game Options page, ensure that the Bacc limit is set correctly, this is your Bill In Limit
On the same page check your Device Options, your BV should be selected as JCM ID003
Check that you have your Comm Board located on the MPU, this is the board that looks like a stick of RAM on the left side of the board
Aristocrat games also require a Comm Board for the UBA, this board sits in the back of the Housing, at the back of the Housing where you see the Gear Cogs this is where the board sits and is connected to the BV Harness via a white connector

Title: Re: uba for aristocrat
Post by: buybestslots on May 25, 2015, 05:05:20 AM

thanks I'll check later to today have auction  at 10am , but I don't recall a board on uba housing

Title: Re: uba for aristocrat
Post by: Harp on May 25, 2015, 05:17:55 AM

I have attached a picture of the board that you should find in the back of the housing for use on Aristocrat Games

Title: Re: uba for aristocrat
Post by: CVslots on May 25, 2015, 09:33:23 AM

Thanks for the info Harp! I have some UBAs that are out of Aristos that are marked 1.71-16, but take new $100s. That must have been the original firmware installed. Thanks again!

Title: Re: uba for aristocrat
Post by: buybestslots on May 25, 2015, 10:41:33 AM

Quote from: Harp on May 25, 2015, 05:17:55 AM

I have attached a picture of the board that you should find in the back of the housing for use on Aristocrat Games

will look   I'm hoping  casino didn't remove them
thanks now I know what I'm looking 4

Title: Re: uba for aristocrat
Post by: Harp on May 25, 2015, 11:15:56 AM

This is how it will look

Title: Re: uba for aristocrat
Post by: buybestslots on May 26, 2015, 04:49:16 AM

everything thing was there in dbv unit   found that this game needed a different  clear chip  the one that worked on other mk 6 would not work on this title  game is up and running at last