New Life Games LLC

**Reel Slots** Gaming Machines => IGT Reel Touch Games => Topic started by: Border01 on June 21, 2019, 05:14:50 PM

Title: Reel touch Reinstall Mslave software
Post by: Border01 on June 21, 2019, 05:14:50 PM

I removed the 1270 board for another machine, ordered a replacement and installed it today. I have an error please reinstall MSlave software. Can not assign a drive letter to the CD-ROM   Any suggestions?

Title: Re: Reel touch Reinstall Mslave software
Post by: qbert on June 21, 2019, 06:03:52 PM

Need picture of error message.
How long has the machine been down.
Did you replace the top box battery?
If you did you need to plug in a keyboard and boot to the bios set up screen by pushing the the delete key when you first turn it on.
Once in the bios screen set the time and date, then save optimized defaults.
Report back

Title: Re: Reel touch Reinstall Mslave software
Post by: RB on June 21, 2019, 08:11:24 PM

qbert is the Reel Touch king. You definitely found the right guy to help you out. We are fortunate to have his expertise at our disposal.

Title: Re: Reel touch Reinstall Mslave software
Post by: Border01 on June 21, 2019, 08:20:04 PM

Yes I have had the great pleasure of meeting him in person.  I learnt not to do anything without his approval on the reel touch machines. My top screen battery was low. Replaced it Machine semi works. Multi denom not working anymore and if I program for my Tito I get a coin out jam. Not sure what’s wrong.

Title: Re: Reel touch Reinstall Mslave software
Post by: qbert on June 22, 2019, 12:08:03 PM

For both issues you will need to key the machine.
Make sure there are no credits on it when you do.
Key then:
1)For the TITO Recheck all settings and make sure the hopper limit is set to zero.

2) For the multi denom make sure you go to key:key chip:Game Select  and activate at least 2 games. Then go back to key denomination screen:player. You should now be able to set denominations. Don't forget to key touch-panel to set buttons.
Let me know how you make out.

Thanks for the kind words guys
Rich

Title: Re: Reel touch Reinstall Mslave software
Post by: Border01 on June 23, 2019, 09:40:40 AM

It went from bad to worse. I had to put a new ticket printer in. Thought I’d do it before I reprogrammed it. Installed the printer than I put the clear chip in. Fired it up and I have no power at all to the MPU now. I’m lost. I turned the power off before any changes. I reseated all I/O boards. When installing the printer I did jiggle some of the wires, the printer moved them as I was putting it in

Title: Re: Reel touch Reinstall Mslave software
Post by: qbert on June 23, 2019, 10:22:34 AM

No power to the bottom?
Try reseating or change the power supply behind the reels. No LEDs on the mpu?

Title: Re: Reel touch Reinstall Mslave software
Post by: Border01 on June 23, 2019, 10:34:52 AM

Top screen works but no lights on the MPU at all

Title: Re: Reel touch Reinstall Mslave software
Post by: Border01 on June 23, 2019, 11:31:52 AM

You were correct. My power supply was weak. Replaced it up again. Now I’ll attempt the multi denomination

Title: Re: Reel touch Reinstall Mslave software
Post by: Border01 on June 23, 2019, 07:01:33 PM

Finally got it working properly. Thank you very much for the assistance.