Author Topic: Bally S6000 Money Bars error 83FO (Read 2255 times)

Doggz2000 · « **on:** February 24, 2022, 08:39:56 AM »

New to me machine, bought clear chip from member of this forum site.
Replaced battery and Did clear procedure according to this site numerous times. Can not get passed 83FO
Tested voltage on mains reads 0v, U18/U20 0v, U30/U35 2.75v
Not sure what else to do
Pics shows chips and recent work done to the board

Sunrise Side · « **Reply #1 on:** February 24, 2022, 10:02:43 AM »

This is from Alan
On the RAM chips U30 and U45 Use a volt meter, Black lead on lower left pin, Red on upper right pin, with chip notch facing away from you. Let us know what your battery voltage shows.

Also before the clear, press the Pseudo and Test button each, a dozen times. The internal contacts do get oxidized .

Doggz2000 · « **Reply #2 on:** February 24, 2022, 12:02:35 PM »

U30 2.75
U45 2.75
I have tested continuity through the Test and Pseudo buttons, they test good but I’ll try it again

Doggz2000 · « **Reply #3 on:** February 24, 2022, 12:09:57 PM »

Pushed both buttons 20x and did full clear, replaced with mains and still 83FO

Sunrise Side · « **Reply #4 on:** February 24, 2022, 12:40:51 PM »

The clear chips you bought, are they the removable type clear chips or the leave in clear chips? It requires a certain procedure for each type. Which do you have?

Doggz2000 · « **Reply #5 on:** February 24, 2022, 02:10:04 PM »

Bought these off of a member here. I asked for the take out ones.

Sunrise Side · « **Reply #6 on:** February 24, 2022, 03:34:37 PM »

Just to confirm, You do not use Dip switch with removable clear chips procedure.

Doggz2000 · « **Reply #7 on:** February 24, 2022, 04:10:00 PM »

I read on this forum that you install clear chips and turn Ds1 #8 ON, then do the Test and Speudo buttons in while turning machine on and wait for full clear. Then #8 off and reinstall mains.
Is this not right?

pbwizard25 · « **Reply #8 on:** February 24, 2022, 05:15:04 PM »

I saw that you are doing a full clear, this will not work. You must do a complete clear.

Doggz2000 · « **Reply #9 on:** February 24, 2022, 05:25:39 PM »

What is the procedure for a complete clear?

Sunrise Side · « **Reply #10 on:** February 24, 2022, 05:55:17 PM »

Removable clear chips you do not use the #8 switch. Leave it off. And do the clear

Doggz2000 · « **Reply #11 on:** February 24, 2022, 06:57:11 PM »

I tried with sw8 off, pushed Test and Pseudo in while turning machine on. Got Credit “0”. Coin in “0” slowly flashing then reels jumped. Turned machine off. Put mains back in and still 83F0.
Did I miss something?

Doggz2000 · « **Reply #12 on:** February 24, 2022, 07:11:40 PM »

Tried it again without pushing anything. Same slow 0 0 Flashing, reels spinning the aligned at seem. Now two dots in the Win Paid. Turned machine off, replaced mains and still 83FO

Sunrise Side · « **Reply #13 on:** February 24, 2022, 07:14:08 PM »

With clear chips installed, Do you press and hold buttons for about 30 seconds, till you see CLC in the display?

Doggz2000 · « **Reply #14 on:** February 24, 2022, 07:31:25 PM »

Held for 35 secs, now I have in the Win Paid a 5.0. flashing with the “0”’s

Sunrise Side · « **Reply #15 on:** February 24, 2022, 07:58:07 PM »

Did the reels spin and calibrate after you installed the original mains? If you have 50 on display close the door

Doggz2000 · « **Reply #16 on:** February 24, 2022, 08:17:26 PM »

No, goes straight to 83F0 and flashing lights

Sunrise Side · « **Reply #17 on:** February 24, 2022, 08:26:17 PM »

83F0 = Invalid SafeRam EPROM

Doggz2000 · « **Reply #18 on:** February 24, 2022, 08:35:19 PM »

Yes, my clear chips are new from a member. Not sure about mains.

Doggz2000 · « **Reply #19 on:** February 25, 2022, 10:38:55 AM »

My Main chips are 2006, which clear chips do I need?

News:

NLG Site Navigation Menu

Author Topic: Bally S6000 Money Bars error 83FO (Read 2255 times)