Progressive Controllers and Displays > Mikohn Progressive Systems
Mikohn Progressive Meter Error Codes
(1/1)
knagl:
Gathered from previous posts from belbenchtech, hotslot101, Ozzy, and others.
Mikohn Error Codes (pre-1998);
There are two general categories of error codes;
Display & Controller.
Display error codes;
C1 Display has lost communication with controller.
Perhaps a broken wire or unplugged.
C2 Current value too long for display.
Parameters incorrectly set.
C3 Verify error on data written to RAM on LED logic.
Jackfile too long?
C4 PROM limit overflow. (Jackpot value exceeds fixed limit in PROM.)
Error in current jackpot value? (Too many digits/symbols.)
Controller error codes;
$C.10 Controller checksum failure.
Usually associated with stand-alone or slave component.
$C.11 Bad reception. (Over 20 over-run framing errors.)
Usually caused by loose fiber connector.
$C.30 Slave controller does not detect master controller.
Improper switch setting on controller?
$C.31 Slave polled but not acknowledged (more than 20 failures).
Error in fiber system. Check all fibers.
*from Mikohn Technical Bulletin Vol. 1, No. 1
Code Description
C1 Communication loss controller to display
C2 Value too long for display on current programmed JP
C3 Test pattern written to RAM on logic when read back has been corrupted
C4 PROM limit overflow. The current jp value exceeds the fixed limit value in the EPROM
C8 Sentinel Timeout (CHAMII, v3.02 only)
C9 Loss of configuration (CHAMII only)
C10 Checksum of a value in the controller has failed
CHAMII+ DISPLAY ERROR CODES
Code Description
C1 Communication Link is down
C2 Metered Amount is too large to fit in window
C5 In MultiLink mode: Jackpot Token is not set to 8 in JPOT.DO file (PSP Message Programming)
C10 Progressive is not set up (use PSP to initialize progressive)
C12 Current Amount is greater than Limit
C14 The selected Machine Serial setting is not supported
C15 Progressive not set up correctly (Base>Limit or Base>Current or Hidden>Limit)
C52 In MS10 Machine Serial setting: A serial machine has gone off-line
CON2 CONTROLLER ERROR CODES
Code Description
C11 Fiber bus communication error in the UART. Over 20 errors have been received from the fiber bus
C12 Programmed JP limit is less than current JP
C13 Over 20 errors have been received from the Tandy 102 or other laptop
C14 Slot machine interface communication error in UART. Over 20 errors have been received from the slot machine interface
C15 Power up JP limit failure
C16 Power brown-out
C17 RAM signature error
C18 Hidden JP (Minimum Value) is equal to or greater than the JP limit (Maximum Value)
C19 Current JP is greater than the JP limit (Maximum Value)
C20 Random Jackpot System Only – Coin-in Buffer
C21 Digit overflow
C30 Slave controller does not detect a master controller
C31 Slave being polled but has not been acknowledged after 20 retries
C32 Slave resend RAM failure
C33 Slave has ACK’d more coins than possible
C34 Master’s fiber pass through has failed after three attempts
C50 MULTI-COM is not responding
C51 Transmission/reception failure
C52 Serial Transmission/reception failure
C53 Serial machine Mystery Pay is not available
C54 Bally MultiComm error: Bad CRC
C55 Bally MultiComm error: Non BCD value
C56 Bally MultiComm error: Invalid group ID
C58 Bally MultiComm error: Wrong sequence number
C59 Bally MultiComm error: Invalid machine ID
C60 Event driven bonus not available.
C61 Event driven bonus Threshold value is 0
C77 Database error
C80 Slave controller does not detect a master present on a Random Bonus game
C81 Slave coin buffer overflow
C82 Random coin matrix buffer overflow
C83 Random coin buffer overflow
C84 Denomination multiplier overflow
SUPERLINK V1.63 AND NEWER ERROR CODES
Code Description
C10 RAM failure is caused by bad checksum or wrong data type
C11 Fiber port serial error
C12 Jackpot group limit error: Current >Limit
C13 Programming port serial error
C14 Serial machine port serial error
C15 Power-up limit failure
C16 Power failure
C17 RAM signature failure: Causes complete factory reset
C18 Jackpot group limit error: Minimum exceeds Limit
C19 Jackpot group limit error: Random
C20 Random coin-in buffer error: Non-BCD value
C21 Digit overflows: a result was larger than 10 digits
C22 Battery backup data recovered ok
C23 Payout amount does not exist in pay-table
C24 Pay-table is invalid: Payout weights do not add up to 100%
C25 Increment value is too large: Value> 0.100 000 00
C26 Machine denomination mismatch
C29 Controller’s password has been expired
C30 Fiber time-out: Slave has not been polled
C31 Fiber time-out: Slave has not been acknowledged
C32 Slave re-sends RAM failure: Bad checksum or wrong data type
C33 Slave has acknowledged more coins than possible
C34 Master’s fiber pass through has failed after 3 attempts
C35 SIB power-up reset
C36 SIB false jackpot
C37 SIB false jackpot canceled
C40 Merchandise controller: Bonus mode is active
C41 Merchandise controller: Bonus mode is inactive
C42 DCU controller: Jackpot queue is overflow, clear jackpot queue
C50 Bally MultiComm time-out: MultiComm not responding to poll
C51 No serial machine is on-line
C52 Serial machine or SIB has gone off-line
C53 Serial machine Mystery Pay is not available
C54 Bally MultiComm error: Bad CRC
C55 Bally MultiComm error: Non BCD value
C56 Bally MultiComm error: Coin buffer overflows
C57 Bally MultiComm error: Invalid group identifier
C58 Bally MultiComm error: Wrong sequence number
C59 Bally MultiComm error: Invalid machine number
C60 Gaming Device: General Tilt
C61 Gaming Device: Power Up Reset or Game Reset
C62 Gaming Device: Coin In Error
C63 Gaming Device: Coin Out Error
C64 Gaming Device: Game RAM or EPROM Error
C65 Gaming Device: Bill Validator Error
C66 Gaming Device: Hopper Empty or Hopper Error
C67 Gaming Device: Reel Tilt
C68 Gaming Device: Reset During Payout
C70 Gaming Device: Game Door Open
C17 Gaming Device: Game Door Close
C72 Gaming Device: Drop Door Open
C73 Gaming Device: Drop Door Close
C74 Gaming Device: Bill Door Open
C75 Gaming Device: Bill Door Close
C77 Machine ID RAM failure: bad checksum or wrong data type
C80 Slave indicates no response from master
C81 Slave coin-in buffer overflows
C82 Random coin-in matrix overflows: more than 99 coins
C83 Random coin-in buffer overflows: more than 9999 coins
C84 Denomination multiplier overflows: result > 9999
C90 Single/Multi-Link: Controller mode is corrupted.
C91 Single/Multi-Link: Jackpot Group number is out of range
C92 Single/Multi-Link: Duplicated machine number
C93 Single/Multi-Link:Link Number is out of range
C94 Multi – Site: Jackpot coin-in contribution is already reported
C95 Communication between SIB - - Gaming Machine is off
C96 Communication between SIB - - Gaming Machine is on
C97 Communication between Controller – SIB is off
C98 Communication between Controller – SIB is on
C99 Auto-Polling Error: Coin-in values lower than previous poll
Navigation
[0] Message Index
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |