Author Topic: Keno igt fortune 2 (Read 4857 times)

Bkiller · « **on:** April 07, 2020, 02:30:57 PM »

Installed a new video board screen is now acting up think vertical sync not a 100% and it coin in timeout error

Stayouttadabunker · « **Reply #1 on:** April 07, 2020, 04:07:29 PM »

I don't understand what you are saying.

Please use punctuation.

Thank you!

Badbaud · « **Reply #2 on:** April 07, 2020, 08:28:18 PM »

What brand of monitor did you use.
If it was a Ceronix, are you sure the video solder jumpers on the bottom of the monitor board are correct?

Amechanic · « **Reply #3 on:** April 07, 2020, 09:08:57 PM »

We need more information on what was change, brand and pictures if possible. What did you use for a replacement? Not all chassis are the same..

Bkiller · « **Reply #4 on:** April 09, 2020, 04:31:28 PM »

Here is where I am at checked all the voltage not sure where to go frome here only payed 20 bucks for the machine

Stayouttadabunker · « **Reply #5 on:** April 09, 2020, 06:23:00 PM »

check your coin hopper then close the door and let us know if any other messages pop up.

Badbaud · « **Reply #6 on:** April 09, 2020, 06:44:36 PM »

Press Cursor Advance under the right fuse then close door.

Bkiller · « **Reply #7 on:** April 09, 2020, 07:12:35 PM »

Tryed it did not help removed hopper put back in reset powered down then back up here is the message showing on the screen

Amechanic · « **Reply #8 on:** April 09, 2020, 07:17:54 PM »

Do you have a reset key? You either need a reset key to clear the hopper extra coin paid error, or by being able to do the reset inside by flipping a switch or a lever. Did you figure out the video problem?

Bkiller · « **Reply #9 on:** April 09, 2020, 07:22:45 PM »

Had no keys with it had to drill them out can reset by hand did nothing

Bkiller · « **Reply #10 on:** April 09, 2020, 07:35:01 PM »

A strange question does anyone know what the output on the hopper should be

Amechanic · « **Reply #11 on:** April 09, 2020, 07:38:18 PM »

I know that the Fortune 1 had a 2 way reset key. One way was for errors, and the other was for Jackpots or accounting.

Badbaud · « **Reply #12 on:** April 09, 2020, 08:16:17 PM »

F2 did not. Here is a schematic of the hopper.

Bkiller · « **Reply #13 on:** April 09, 2020, 08:41:12 PM »

Seems like no power to the hopper

Badbaud · « **Reply #14 on:** April 09, 2020, 08:53:21 PM »

Just on that goofy schematic from IGT.
Attached is a section of the I/O board schematic.
U31 and U39 are involved in detecting coin out.
I would suggest replacing U31 first.
A CD40106 is a substitute for the U31 shown.
Also check for a blown trace around that chip.

Bkiller · « **Reply #15 on:** April 09, 2020, 09:05:25 PM »

Here is what I have at the plug

Bkiller · « **Reply #16 on:** April 09, 2020, 09:14:11 PM »

Quote from: Badbaud on April 09, 2020, 08:53:21 PM

Just on that goofy schematic from IGT.
Attached is a section of the I/O board schematic.
U31 and U39 are involved in detecting coin out.
I would suggest replacing U31 first.
A CD40106 is a substitute for the U31 shown.
Also check for a blown trace around that chip.

Looks like refurbished board

Badbaud · « **Reply #17 on:** April 09, 2020, 09:31:25 PM »

That is the MPU board, the I/O section is on a separate metal tray.

Amechanic · « **Reply #18 on:** April 09, 2020, 09:38:03 PM »

Thatâ€™s right. The F2 had two board trays. The second had two boards. One was an I/O and the second was sound?

Bkiller · « **Reply #19 on:** April 09, 2020, 09:43:48 PM »

All 3 boards are in like new condition

News:

NLG Site Navigation Menu

Author Topic: Keno igt fortune 2 (Read 4857 times)