New Life Games LLC
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length

News:

Welcome to the NewLifeGames.com message forum! 

 


NLG Site Navigation Menu


Archives of old posts can be found at...... Newlifegames.net/nlg/

Author Topic: S plus RWB powering up issues  (Read 2845 times)

0 Members and 1 Guest are viewing this topic.

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
S plus RWB powering up issues
« on: November 11, 2022, 05:06:09 PM »
Hello all,

Just picked up a non-working Splus RWB machine. Lights power up and bill validator cycles then nothing. I read where it could be power not getting to board. I checked fuses with a meter and they are good. Can hear humming start and stop when fuses installed and taken out. Also checked pins in back to board that everyone states are a weak point in these machines. No burn marks. Cleaned pins Pushed on well, but nothing. No reel spins or display showing. Reels are free so no power to those either. What is next?
 CORRECTION: Sorry i am new at this...Wheels are getting power and tighten up when powering on, but nothing after...

Will say that they didn't have reset key so unable to try that, unless i cross the wires, but havent read that will do anything until reels activate. True?

Any help appreciated.
« Last Edit: June 15, 2023, 03:58:10 PM by jonbbrew »
How about throwing me some positive KARMA love by clicking on the left!

Offline Tilt

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 4402
  • Reputation Power: 384
  • Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!
  • Gender: Male
Re: S plus RWB powering up issues
« Reply #1 on: November 11, 2022, 07:14:49 PM »
Remove the MPU board (with power off of course) and post a picture of it.  Pics here have to be less than 1MB, so resize if necessary to get under that limitation.

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
Re: S plus RWB powering up issues
« Reply #2 on: November 12, 2022, 11:07:11 AM »
Thanks for the help. I’m puzzled.
How about throwing me some positive KARMA love by clicking on the left!

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
S+ Still Reels wont spin on power/boot up. Next?
« Reply #3 on: November 12, 2022, 01:19:27 PM »
Hello,
Trying to get new to me S+ RWB running. On power/boot up...Bill Validator and front tubes light, as well as reels stiffen but do not spin. Connector and fuses good. What next?
How about throwing me some positive KARMA love by clicking on the left!

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
Re: S+ Still Reels wont spin on power/boot up. Next?
« Reply #4 on: November 12, 2022, 03:52:51 PM »
Reposting with different subject as it is pulling a very faint 21 code.
How about throwing me some positive KARMA love by clicking on the left!

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
S+ faint 21 code
« Reply #5 on: November 12, 2022, 03:56:12 PM »
Hello all,

Still trying to figure out this new to me machine. Powering/booting up reels firm, no spin. I missed it at first but very faint 21 error code. Looking at other posts i ran across this diagram where it said 24 volts should be at pin 4. Not nearly that much but cant recall exact number. I can get that if it makes a difference but far from 24. Checked continuity of ground and it appears good. What next?
How about throwing me some positive KARMA love by clicking on the left!

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #6 on: November 12, 2022, 04:23:23 PM »
here is the diagram i was reading about...
How about throwing me some positive KARMA love by clicking on the left!

Offline sixcardmark

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3854
  • Reputation Power: 235
  • sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #7 on: November 12, 2022, 04:28:04 PM »
21 is coin in optics.

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #8 on: November 12, 2022, 04:34:43 PM »
21 is coin in optics.

Yes that is where i am focusing. That is the pin diagram for the power to the CC. As far as what are all of the issues i can check, that's where i am knowledgeless and need help.
How about throwing me some positive KARMA love by clicking on the left!

Offline sixcardmark

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3854
  • Reputation Power: 235
  • sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #9 on: November 12, 2022, 04:36:13 PM »
Coin in optics board is right below the CC. Clean the 3 sensors first.

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #10 on: November 12, 2022, 04:54:59 PM »
Coin in optics board is right below the CC. Clean the 3 sensors first.
how do i get to them? I can see where the coin moves through but dont see how to get it off to clean.
How about throwing me some positive KARMA love by clicking on the left!

Offline sixcardmark

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3854
  • Reputation Power: 235
  • sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #11 on: November 12, 2022, 05:01:23 PM »
Remove the CC and you will find two screws.  You have to remove the plate the CC clips onto.  You can try to clean it with a qtip after removing the CC without removing the plate.  Do NOT use alcohol on sensors.

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #12 on: November 12, 2022, 05:10:53 PM »
Remove the CC and you will find two screws.  You have to remove the plate the CC clips onto.  You can try to clean it with a qtip after removing the CC without removing the plate.  Do NOT use alcohol on sensors.

thanks i will give that a try shortly  That alone could clear a 21?
How about throwing me some positive KARMA love by clicking on the left!

Offline sixcardmark

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 3854
  • Reputation Power: 235
  • sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!sixcardmark Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #13 on: November 12, 2022, 05:57:48 PM »
Yes it could.  It also could need replaced or be a pin/wire on its harness. Always open/close door a few times to see if error clears.

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
Re: S+ faint 21 code
« Reply #14 on: November 12, 2022, 07:44:48 PM »
Yes it could.  It also could need replaced or be a pin/wire on its harness. Always open/close door a few times to see if error clears.

What would make the LCD be faint?
How about throwing me some positive KARMA love by clicking on the left!

Offline Telemaster

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 35
  • Reputation Power: 2
  • Telemaster New User has no influence.
  • NLG
Re: S plus RWB powering up issues
« Reply #15 on: November 12, 2022, 08:26:08 PM »
Do you get anything on the display?

Offline Stayouttadabunker

  • Topic Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 5429
  • Reputation Power: 405
  • Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: S plus RWB powering up issues
« Reply #16 on: November 13, 2022, 08:45:47 AM »
With the power switch OFF, ( always turn off the power when working on these machines) pull out the 3 fuses one at a time, and put back in so you don't mix them up.
What are the amperage of each one?
They should be...>>>

6A
8A
6A

From top to bottom, on front of the power supply box.

I cannot see your SP and SS chips too clearly in their sockets in the photo you submitted.
They appear to be in the correct orientation, but it's not that clear.
Let's see what's written on the labels on top of the chips.
It would be good to see if there's any legs folded under the chip body.

Also, the dip switches on the right.
Usually dip switches numbered 1-4 are push downwards in the ON position, while 5-8 are upwards in the OFF position for home use...It's not that important tho.

It sounds like you're getting power to the reels....so that's a good thing.
Fiddle around with the display connector...maybe its loose?
Which display do you have? The long one or the short one?
Can you give us a photo of the back of the display ?
Esp. where the connectors are?
They should be just on top of the back panel and black plastic.
We'll help you get your machine running for sure.
Remember, the more you tell us - the better we can help you!

Consider becoming a regular contributing member, which helps pay costs to keep this site up and running so you can keep your machine up and running :)

Offline Tilt

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 4402
  • Reputation Power: 384
  • Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!
  • Gender: Male
Re: S plus RWB powering up issues
« Reply #17 on: November 13, 2022, 09:36:14 AM »
Bunker, he's got three different topics started now for this same machine.  Maybe you can merge them all together and get rid of the duplicate/un-necessary stuff?

https://newlifegames.com/nlg/index.php?topic=37746.0

https://newlifegames.com/nlg/index.php?topic=37741.0


Offline a69mopar

  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2104
  • Reputation Power: 83
  • a69mopar Is a force to reckon with.a69mopar Is a force to reckon with.a69mopar Is a force to reckon with.a69mopar Is a force to reckon with.a69mopar Is a force to reckon with.a69mopar Is a force to reckon with.a69mopar Is a force to reckon with.a69mopar Is a force to reckon with.
  • Gender: Male
  • NLG
    • www.gtaslots.com
Re: S plus RWB powering up issues
« Reply #18 on: November 13, 2022, 11:59:38 AM »
merged.  I left the topics, so it will be easier to follow.

Thanks,
Wayne

Offline jonbbrew

  • Contributing NLG Member
  • NLG Member 251 to 500 Posts
  • *
  • Posts: 401
  • Reputation Power: 33
  • jonbbrew Is working their way up.jonbbrew Is working their way up.jonbbrew Is working their way up.
  • Gender: Male
  • NLG
Re: S plus RWB powering up issues
« Reply #19 on: November 13, 2022, 03:58:16 PM »
How about throwing me some positive KARMA love by clicking on the left!

 

Cell Phone and Pad Mode

imode wap wap2

NLG Archives

Archives @ newlifegames.net Wayback Machine

Contact Us

NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442
If you find this site helpful, please consider becoming a Contributing NLG Member with a monthly subscription to help cover the cost of pizza, coffee, aspirin, hosting, and bandwidth.
Contributing Members: get unlimited personal messages, can save topics and replies as drafts,
can post to the Classified ads, get unlimited access to the downloads, and also get this minty badge:



**Subscription Link** (Click Here) **Subscription Link**



           
If you would rather remain anonymous Thank You or just want to help support the site, please use this "make a donation" button:




From your entire NLG staff, thank you for supporting NLG.


New Life Games LLC 1788 HIGHWAY 95 UNIT 30 BULLHEAD CITY AZ 86442




Newlifegames.com     Newlifegames.net     Newlifegames.org

Newlifegame.com     Newlifegame.net     Newlifegame.org    Newlifegames.us

   New Life Games     NewLifeGames  NLG

 We Bring new Life to old Games    1-888-NLG-SLOTS

Are all Copyright and Trademarks of New Life Games LLC 1992 - 2022


FAIR USE NOTICE:



This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml
If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.




The NewLifeGames.com website is optimized for use with Firefox and a minimum screen resolution of 1600 x 900 pixels.

SimplePortal 2.3.5 © 2008-2012, SimplePortal