New Life Games LLC
**Video Poker, Keno, Slots, 21** Gaming machines => Pot-O-Gold => Topic started by: Xtremenichols on February 07, 2020, 03:37:25 PM
-
GOLD FINGER T1000 R0 PCB WILL NOT CALIBATE ELO TOUCHSCREEN IN NOT TYPE OF PIN CONFIG PERIOD
CHIPSET IS 580 ELO SCREEN IS BRAND NEW NOT USED BUT IT IS IN THE 1939L FAMILY
NOW PEOPLE TALK ABOUT THEY MAY HAVE TO BE MODDED BUT I TOOK THAT IS WITH OLD POG BOARDS MY BOARD IS MADE IN 2018 WITH A VGA OUTPUT
I TRIED DIFFERINT CABLES ECC. NEVER HAD THIS PROBLEM BEFORE ELO 280 BLUE SCREEN I TOUCHE THE BOTTOM X THE TOP X APPEAERS
YOU TOUCH THE TOP X DOES NOTHING NEVER LEAVES FROM THAT POINT ON!!!!!!!!
SO PLEASE TO ANYONE THAT CAN HELP ME GET THREW THIS HAIR PULLING PROBLEM I WILL BE THANKFUL :thank_you: :EmoticonHelp4: :fryingpan: :banghead:
-
AND IF SOMEONE MAY HAVE A TURE PINOUT TO THIS NEW POG PCB WOULD BE HELPFULL ALL SO THANKS :CaptainHappy: :CaptainHappy:
-
HERE ARE SOME PICS OF THE PCB :propeller:
-
Did you get that off of Alibaba?
That's a Chinese board.
-
NO I GOT IT OFF EBAY FAR AS THE BAORD WORKING ITS SEEMS FINE ITS JUST THE SAME PROBLEM OF CALIBATING THIS 1939L ELO TOUCHSCREENS I BEEN SCREACHING AND READING ALL OVER THE INTERNET FOR WHAT I HAVE SEEN SO FAR YOU HAVE TO USE A DIFFERNT FIRMWARE ON THEE SCREEN
IF WE CAN SOLVE THIS I ACTUALLY LIKE THIS BOARD BETTER CAUSE ITS ALOT EASIER TO TROUBLESHOOT THAT THE T340+ BOARDS
-
Get a Goldfiger touchscreen instead? The ELO's are for computers really.
-
YES I BEEN WANTING TO TRY ONE OF THOSE SCREEN BUT CANT FIND NOONE THAT HAS AND CANT FIND TO BUY WITHOUT PAYING A ARM AND A LEG FOR IT TOO I USED TO BE IT THE TECH FIELD ALL THREW GROWING I.T. SERVICES IN PLANTS LIKE KRAFT FOODS AND CATERPILLER RETIRES BOUGHT A BAR AND GOT IN THE GAMING SIDE OF IT I DID ALL MA SERVICE TO MY MACHINES DOWN TO MY SLOTS BUT MY HEALTH CAUGHT UP WITH ME AND HAVE TO GET OUT THE BAR BUSINNESS A FEW YEARS AGO AND BEEN ON DISABILITY EVERY SINCE TIMES ARE HARD RIGHT NOW AND A FRIEND HAS A BAR THATS GOING TO LET SET A FEW MACHINES UP THERE
SO IS THERE AWAY FOR ALL OF US TO COME TO FIND THE FIX TO THIS ISSUE IM IN DYING NEED OF HELP AND I KNOW ALOT OF OTHER PEOPLE ARE HAVING THE SAME PROBLEMS SO WE WILL BE HELPING THEM ALSO I KNOW IM NEW TO THE GROUP BUT I JUST FOUND THE GROUP AND IM NOT GOING NO WHERE IM HERE TO HELP OTHERS AS WELL
-
NOW THE SCREENS I USE ITS A ELO TOUCH AND IT IS IN 1939L FAMILY BUT OTHER THAN THAT ITS ALOT MORE DURABLE IT THATS ALOT ABUSE IT IS COMPLETLY WATER THESE MONITORS COME FROM KRAFT FOODS THEY GET BEAT ON 24 HRS A DAY AND WASHED DOWN WITH 1000PSI OF HOT EVERY NIGHT I GET THEM BRAND NEW CAUSE I KNOW SOMEONE TYPE OF DEAL I BEEN USING THESE MONITORS FOR YEARS NEVER ONCE HAVE ONE TO BREAK ON ME HERE IS SOME PICS
-
HERE ARE THE PICS ON MONITOR :thank_you:
-
AND TO ANYONE ELSE THATS HAVING THE SAME PROBLEMS OR ISSUES PLEASE COMMENT CAUSE IT THINGS YOU ALL MAY HAVE TRIED THAT I HAVENT AND ITS THINGS I MAY HAVE TRIED THAT YALL HAVENT WE CAN FIND THE FIX IF ALL WORK TOGETHER AND I CAN TELL YOU IF DOESNT HAVE NOTHING TO DO WITH THE BOARD AND THE DIP SWITCHES ON THE BOARD I HAVE RULED THEM OUT IN EVERY WAY :banghead: :fryingpan: :hissyfit:
-
What are all the numbers on the small board that's connected between the touchscreen and the main LCD circuit board?
Maybe I can help you find the configuration of the pins that controls the orientation of the touchscreen?
No one else seems to be helping you so I'm your best shot here...lol
I had to find out the pinouts of an IGT Game King touchscreen once and it wasn't easy but I succeeded.
-
OK LET ME TAKE THE SCREEN APART
-
A ribbon cable goes to the small board - nothing you can do about that.
However, coming out the other end of it should be 5-6 wires - that's the configuration of wiring
you need to figure out to make the touchscreen respond correctly to touch.
-
HERE THE PICS OF THE CONTROLLER
-
ITS A 20 PIN COMING OF THE CONTROLLER
-
The other White connector only has 5 pins right?
That's the one maybe?
Gotta find a drawing for this TS controller card...>>>
https://www.touchwindow.com/p/E329179.html (https://www.touchwindow.com/p/E329179.html)
This page shows that it has 5volts powering it up...>>>
https://www.touchwindow.com/mm5/graphics/00000001/elo/2218_vs_2216.pdf (https://www.touchwindow.com/mm5/graphics/00000001/elo/2218_vs_2216.pdf)
You need to get out your multimeter and find out which wire is the ground wire which is the 5volt wire.
The remaining three wires will be for the TS (Touch screen) along with the common ground wire.
Found a drawing of the controller for ya...>>>
https://docs.elotouch.com/components/touchscreen-components/5-wire-resistive-accutouch/2218Controller.pdf (https://docs.elotouch.com/components/touchscreen-components/5-wire-resistive-accutouch/2218Controller.pdf)
-
IM GETTING VOLTAGE ON THE 4TH PIN DOWN ON P2 4.8V BUT MY METER IS ALITTE OFF
-
Nevermind that.
On the [P2] connector, you need to swap two pins to get your touchscreen to orientate correctly.
I'd swap upper right with lower left.
What are the colors of the wires on the harness that connects to the [P2] header?
Look at this drawing from the one I gave you.
Click on photo below to enlarge if needed...>>>
-
I HAVE NO WAY ODOING THAT IT A RIBBON CABLE PIC UNLESS YOU KNOW ANOTHER WAY
-
Nope.
Your touchscreen controller is incompatible with your game.
Especially if that ribbon cable is coming from the controller to the touchscreen.
Only possible way is to make a wire harness and swap to pins.
But basically, it just wasn't designed for your gameboard.
-
WHAT IF I MADE A JUMPER HARNESS WOULD THAT FIX IT THO
I CAN MAKE THE HARNESS NO PROBLEM
-
I cannot guarantee it will work.
This is why I didn't recommend it.
What you want to make is a harness from the ribbon cable end to the touchscreen and swap the 2 diagonal pins from the drawing in Reply #17.
Looking at the configuration, I believe pin#1 swapped with Pin#5....if it doesn't work, put the wires back immediately and swap the other pairs.
Every time you swap a pair of touchscreen pins, the screen will respond differently to your touches.
Keeping swapping pairs and testing systematically (make notes of each swap) until you get it to work the way you want and report back whether or not if it worked or blows up the controller board...lol
Have fun...you'll get it.
-
YEA LIKE A HARD WIRED ADAPTER TO PLUG IN BOTH SIDES
-
I HAVE THIS LITTLE KIT THAT I USE WITH MY RASHBERRY PI S
I MAKE SOMETHING OUT IT
-
I WILL KEEP YOU POSTED AND THANK YOU FOR ALL YOUR HELP SO FAR IT REALLY MEANS ALOT THANK YOU :thank_you: :waving_flag: :waving_flag: :thank_you: