**Video Poker, Keno, Slots, 21** Gaming machines > Scientific Games (TwinStar, ArgOS)

bb3 blade to Argos

(1/2) > >>

cheon2:
i am looking for a guide or video to switch from bb3 blade to Argos and back.
i think i have everything i need to do this.

gbknox:
Cheon2
For full disclaimer, there are no guarantee's this will work but it's a start.

Thinks you will need for the install.
1. ArgOS Bios (ABIP03)
2. USB ArgOS Installer (AIN0000000X image installer)
3. USB with OS/WIN/JURS images
4. MultiLink Paytable USB dongle (all the Lock it Link games will need this. There are some ArgOS games that don't require a MultiLink Paytable)
5. ArgOS Game to install
6. RJ45 Cat5e Patch cable (an ethernet switch is preferable). You don't need internet access. I wouldn't expose the cabinet to the outside world anyway.

These instructions are fairly old but they should get you started. You should be able to skip #1 but for good measures, I would do this anyway with a WMS BB3 Clear CF Card. If the game you are loading is a Lock it Link Game, you will need a MultiLink Paytable USB and you will also need to connect one of the ethernet RJ45's to a network switch. The cabinet can be the only device on the switch. If you don't have a network switch, you can just insert a Cat5e cable to both ethernet ports. It does not have to be a crossover cable, just a short patch cable with one end in eth0 and the other in eth1. If you have multiple Blade cabinets and a single MultiLink Paytable USB, you will want to use a network switch and connect the additional cabinets to the switch so all cabinets can see the MultiLink Paytable for the progressive setup.

My apologies is I missed anything. I wrote the procedure quite a while ago and now, I'm on autopilot now when I setup a cabinet. 

1.   If the Machine has been running a WMS Game, Run a NVRAM Clear on the cabinet.
2.   Shut Down the Cabinet
3.   Remove the Jurisdiction and Bio’s Chipsets (normally Blue and Yellow).
4.   Install the ArgOS Bio’s but leave the Jurisdiction socket open.
5.   Insert the Installer USB Stick (AIN0000000E or newer) and boot the cabinet up. Other version of the installer should work just fine.
6.   Select the “Factory Reset” option. This will format the Hard Drive and clear the EPROM and NVRAM. Make sure the only USB stick inserted is the installer because I don't think "Factory Reset" will be enabled if there is another USB inserted into the cabinet.
7.   Insert the OS/Win/JURS USB. Select all the files and then select Install. Make sure your Windows image on the installer USB is a AWI03X version for a Blade.
8.   Remove the OS/Win/JURS USB and insert the Game USB (Piggy, Diamonds, Cats, Night Life, etc.). Only 1 game will install. If you want another game, select install and the prior game will be removed.
9.   Power the Cabinet down and remove the USB drives (installer and OS/Win/JURS) from the Cabinet.
10.   Install the DRM for the Game along with an ArgOS MultiLink Paytable (required for Lock It Link Progressive Games) and power the cabinet up.
11.   Skip the NVRAM Clear and EZConfig. NVRAM clear has already been completed on a Factory Reset and the loading of the OS/WIN/JURS.
12.   Setup Clock, Time Zone, SAS Primary, Pay Tables, Printers, Bill Validator, etc. Printer and Bill Validator should be selected automaticly.
13.   From the top slightly right of the middle of the screen, select "MultiLink Bank Controller". Make sure you “Start the Progressive” after setup.
14.   From the dropdown in the upper right part of the home screen, select "EGM Mode" again and go into the Progressive setting and select the "Configure Controllers" button. The select "MMLNAP" (I believe) from the dropdown, select the MultiLink Host you just added in step #13.

Go back to the home screen and make sure there aren't any other Pending Tilts other than "Main Door Open" and "Setup Menu Entered". If no other Pending Tilts are visible, You should be able to select Exit in the top right and you are in business and ready to play.

To Switch back to NBOT (WMS), power off the cabinet, remove the ABIP03 Bios and reinstall the NBOT Bios and JURS chip. Insert the BB3 Clear CF Card and clear the NVRAM and start over with the WMS OS/Game installation.

You might have to do this setup multiple times unless the instructions are really good or you see past things I missed in the instructions. I never, never get it right on the first pass.

Good luck with the setup. Eventually you will get your Autopilot tuned in and do this in your sleep.

Please chime in if I missed any of the instructions need to be tweaked.

cheon2:
thanks
this will get me started :hail:

The laneman:
Will this work on a BB2 converted to a BB3 or does it have to be a blade?

The laneman:
^^^anyone try this on a bb2e converted to a bb3?

Navigation

[0] Message Index

[#] Next page