Author Topic: Having a problem removing games G23 (Read 2819 times)

MazzMayhem · « **on:** July 12, 2022, 08:32:58 AM »

Hello, I tried removing games from my G23 for the first time and received this message “protocol that contains legacy meter changes has rejected game removal”

RodneyK · « **Reply #1 on:** July 12, 2022, 09:31:08 AM »

From Morspeed in 2017

It is weird that you can't load games with the tito enabled because I have no problems with it. There may be a setting somewhere that need to be changed. Try this:
Machine Setup Requirements to allow theme installation and removal using Package Management:
1. Navigate to Setup>Communication>Protocol> G2S>G2S must be Disabled (Protocol Enabled - NO) Package Management option will not be shown on the menus if G2S is Enabled.
2. Navigate to Setup>Communication>Protocol> G2S and set Protocol that controls Legacy Meter Change setting to NOT REQUIRED

sixcardmark · « **Reply #2 on:** July 12, 2022, 09:37:12 AM »

Also disable games you are going to remove before removing.

MazzMayhem · « **Reply #3 on:** July 12, 2022, 01:18:53 PM »

Thank you very much Rodney, Mark I will check back in with you guys when I get home.

millionaire2k · « **Reply #4 on:** July 12, 2022, 01:21:08 PM »

Also your NVRAM usage is very low. Why remove games? You could just disable.

MazzMayhem · « **Reply #5 on:** July 12, 2022, 06:18:06 PM »

Worked perfectly thank you for your time and the info. The only issue I need to resolve now is getting the machine to recognize the bv. I’m thinking that just might be a setting issue as well. I’m getting a bv offline ID:0 message. I have tried switching usb cables, switching hubs, swapped heads and cash cans no change.

sixcardmark · « **Reply #6 on:** July 12, 2022, 06:55:30 PM »

Quote from: millionaire2k on July 12, 2022, 01:21:08 PM

Also your NVRAM usage is very low. Why remove games? You could just disable.

Games use up NVram even when not enabled.

RodneyK · « **Reply #7 on:** July 12, 2022, 07:03:15 PM »

On the BV have you tried a different USB port on the machine side? Too many USBs plugged in at one time can cause issues too. From comments made in other threads about this and this machine I think it just might not be the correctly programmed BV. Does it ever cycle? Is it getting power?

millionaire2k · « **Reply #8 on:** July 13, 2022, 03:20:31 AM »

Quote from: sixcardmark on July 12, 2022, 06:55:30 PM

Quote from: millionaire2k on July 12, 2022, 01:21:08 PM
Also your NVRAM usage is very low. Why remove games? You could just disable.
Games use up NVram even when not enabled.

I know, but he has a lot of free space (would gain a little back by disabling them) And I just personally wouldn't remove them if my NVRAM was below 40%. It was just a suggestion.

MazzMayhem · « **Reply #9 on:** July 18, 2022, 06:15:38 PM »

Yes Rodney it is getting power and it cycles, I just get a steady blinking green light. I’m thinking it’s either the interface board or the bv head needs to be flashed. I bought this machine recently so I have never seen this bv operational . I did just receive a dongle farm that I am installing at the moment, just hoping this might solve the problem. We shall see.

sixcardmark · « **Reply #10 on:** July 18, 2022, 06:33:10 PM »

Is the other BV cable plugged in right under the usb cable under the printer?

MazzMayhem · « **Reply #11 on:** July 18, 2022, 06:34:33 PM »

No Mark

sixcardmark · « **Reply #12 on:** July 18, 2022, 06:39:45 PM »

Plug it in, here's a pic:

MazzMayhem · « **Reply #13 on:** July 18, 2022, 06:52:47 PM »

I’m sorry Mark yes that one is plugged in. I thought you were talking about the 2 pin connector coming out of the back of the bv. That one is not connected.

sixcardmark · « **Reply #14 on:** July 18, 2022, 06:59:38 PM »

My 2 pin is connected.

MazzMayhem · « **Reply #15 on:** July 18, 2022, 07:00:59 PM »

Do you have a Mei?

sixcardmark · « **Reply #16 on:** July 18, 2022, 07:03:14 PM »

yes. I guess the BV bezel light goes thru the 2 pin.

sixcardmark · « **Reply #17 on:** July 18, 2022, 07:09:02 PM »

A working mei head from a S2000/game king will work. Insert tito tickets upside down.

MazzMayhem · « **Reply #18 on:** July 18, 2022, 08:17:19 PM »

I connected the 2 pin that was unplugged started up the machine and now I’m getting a “S” spare door is open? No idea what that is?

sixcardmark · « **Reply #19 on:** July 18, 2022, 08:44:54 PM »

S or s? Capital S is stacker door.

News:

NLG Site Navigation Menu

Author Topic: Having a problem removing games G23 (Read 2819 times)