New Life Games LLC

Bill Validators, Currency Acceptors and Printers => JCM WBA 10, 11, 12, 13, 14, 20, 21, 22, and 23 Bill Validators => Topic started by: Wayout440 on April 23, 2023, 10:22:07 AM

Title: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Wayout440 on April 23, 2023, 10:22:07 AM: The yellow entry bezel that attaches to the front of my JCM WBA has a small board with status LEDs. It has a two prong plug socket. I have no wire to plug into that. I'm sure it must plug in some on the bill validator. Anyone have info on this? Thanks, Wayout
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: sixcardmark on April 23, 2023, 10:56:22 AM: This is for sentry smart bezel I believe: https://www.ebay.com/itm/304798467342?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ybfjdik9t_e&sssrc=2047675&ssuid=bu-pVdC8TCe&widget_ver=artemis&media=COPY (https://www.ebay.com/itm/304798467342?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ybfjdik9t_e&sssrc=2047675&ssuid=bu-pVdC8TCe&widget_ver=artemis&media=COPY) Not sure what you are looking for.
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Stayouttadabunker on April 23, 2023, 10:58:02 AM: Like this?....>>>

https://www.ebay.com/itm/285171445736?chn=ps&mkevt=1&mkcid=28 (https://www.ebay.com/itm/285171445736?chn=ps&mkevt=1&mkcid=28)
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Wayout440 on April 23, 2023, 11:17:23 AM: No. Only two pin to bezel. Not four, and I don't need extra junk. Just the cable
If someone tells me where it goes and pinout, I can make one.
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Stayouttadabunker on April 23, 2023, 05:51:49 PM: The link I gave you had cables with two-pins.
Why don't you contact the seller and ask they will sell one of them?
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Wayout440 on April 24, 2023, 05:38:53 AM: I found the info I needed in a manual. I think the connector on the LED board in the bezel is a standard Micro PH 2-pin, will just have to diode check for polarity.
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Wayout440 on April 24, 2023, 12:56:07 PM: Does anyone actually have this plugged in and can share info/pics?
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Wayout440 on April 25, 2023, 12:38:51 PM: With the LED bezel wired to pins 1&2 of CN3, the two green LEDs light up solid during power up and initial cycling. They turn of and blink once at the end of cycling and remain off. The valudator accepts bills but nothing happens with the LEDs they just remain off. I thought the purpose of the LED indicator lamps were to be illuminated when the machine is ready to accept a bill.
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: sixcardmark on April 25, 2023, 03:28:56 PM: Quote from: Wayout440 on April 24, 2023, 12:56:07 PM
Does anyone actually have this plugged in and can share info/pics?
What machine is this on?
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Wayout440 on April 25, 2023, 04:02:42 PM: Reel 'em In WMS 550
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Wayout440 on April 26, 2023, 05:05:06 PM: I tried tapping off pins 1&2 of CN2, no dice. Frustrated that there is nobody out there that can help with information as to hooking this up. The bezel appears to be a mass produced product for JCM WBA validators, as it is molded to slide on to the front of the transport. Just can't figure out what the LED indicators are supposed to connect to.
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: a69mopar on April 26, 2023, 06:07:34 PM: Some bill entries connected to wires from the rear connector harness. I'll take a look tomorrow to see.

Thanks,
Wayne
Title: Re: Yellow entry bezel WBA missing wire to plug into two pin jack.
Post by: Wayout440 on April 27, 2023, 12:36:11 PM: I figured out how and where to wire with the RS232 Board occupying CN2 connector. This is my workaround.