New Life Games LLC
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length

News:

Welcome to the NewLifeGames.com message forum! 

 


NLG Site Navigation Menu


Archives of old posts can be found at...... Newlifegames.net/nlg/

Author Topic: WMS Model 40x Dotmation Upper Power Supply Fix  (Read 8832 times)

0 Members and 1 Guest are viewing this topic.

Offline knagl

  • Kevin
  • NLG Site Administrator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2002
  • Reputation Power: 168
  • knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!
  • Gender: Male
WMS Model 40x Dotmation Upper Power Supply Fix
« on: July 05, 2020, 10:34:33 PM »
Moderator's note: this is a re-post from the old NLG forum, created by member cfh.  Big thanks to Clay for creating this tutorial and related images.

I should mention before going down this road that ONE computer power supply can be used to replace both the upper and lower power supplies. That is covered in another post. But sometimes people want to do things this way. So for completeness, here's a technique to show how to replace just the upper power supply.

So we covered replacing the lower main power supply on Williams Dotmation model 40x slot machines. I figured should probably show how to fix the upper dotmation power supply.

Yes there are two different power supplies in a Williams model 40x slot machine. The lower (main) power supply gives +5, +12, -12, +20 volts for the processor boards. But there is a second power supply that lives behind the DMD (dot matrix display) box. This power supply takes 120 volts AC input and puts out 12 volts DC output. This 12 vdc is fed to the Dot Matrix Controller (DMC) and the DMD. Then both of these boards take the input 12 vdc and manipulate it as they need.  (For example the DMD turns the 12 volts into +/- 120 volts DC).

The problem with the upper Dotmation power supply is similar to the lower main power supply, it dies a lot!  Though slightly better than the lower power supply (it only outputs one voltage), it's still problematic.  Repair is definately possible, but replacement seems to be where most people want to go.

Note that the upper Dotmation power supply and the lower main power supply are made by the same company, and generally look the same!  That is, don't confuse these two power supplies. If for example you install the Dotmation power supply mistakenly in the lower power supply "can", you WILL smoke the I/O board, processor board, and the meter board. (Please don't ask me how i know this!)

Original Lower Power supply part#: PU110-31A
Original Dotmation Power supply part#: PU110-12A

Note the connectors are EXACTLY the same for both power supplies! (though the output voltages are different.) Though you didn't need to know this for this repair, I thought it was important to mention it.



Anyway, back to replacing the upper Dotmation power supply.

The current trend is to use a video game switching power supply. For about $25 this is a decent solution, as these power supplies are small, cheap, and work well. But frankly you could make your own linear unregulated power supply with a 120 volt to 12 volt transformer, a bridge rectifier, and a 10,000 mfd filter cap. (But most people don't want to do that work.)

The original Dotmation P.S. puts out 12 volts at 9 amps.  The replacement video game P.S. i used only puts out 12 volts at 4 amps. It works, but i would say really 5 amps should be a bare minimum output for the new power supply's 12 volts.

I suspect the reason Wms did not use just one power supply for the dotmation and the rest of the game has to do with RF interference. Anytime you have a power line that is long, there is potential for RF interference. They need to have these devices approved, and just didn't want to worry about RF interference. So having a separate PS right next to the DMD limits the potential RF interference.
Likewise, notice on the lower PS the voltage cable from the PS "metal can" to the backbox is very short

i've been running these 12 volt 4 amp power supplies for the dotmation on several machines. i'm not a casino, but they have been running fine and without any issues. If you look at pinballs like Baywatch (which use the same dot matrix display), they don't have more than 4amps of 12 volts running their display. So the 4amps is probably fine (though again, i wouldn't go any lower).

My Dotmation power supply replacement procedure is shown in pictures below. It's not a "cut and hack" approach (though I'm betting most people take that approach.)

The steps are as follows:

Parts:
(10) Molex trifurcon crimp connectors pins #08-52-0113
(2) Extra long Molex male header pins# 10-01-2270
    (or 09-62-6104 or 09-52-3102). Cut to length desired.
(1) Molex connector housing part# 09-50-3131 (13 pin)
(1) Molex connector housing part# 09-50-3051 (5 pin)
(1) Molex 156" polarized peg, part# 15-04-0219 for the new 13 pin connector
(1) 75 ohm 1/4 resistor
(5) feet of black 18 guage wire
(3) feet of red 18 gauge wire
(1) foot of white 18 gauge wire
(1) foot of green 18 gauge wire

1. Power off, remove top glass. Then unscrew two retaining screws on the DMD panel metal "can". Fold the DMD down and out of the way (or unplug the DMD completely and set aside).

2. Remove the two connectors from the original dotmation power supply (one 5 pin, one 13 pin).  The original Dotmation p.s. can be left installed or removed.

3. Make two cables that mate to the original Dotmation power supply cables removed in step#2 above. These are a 5 pin and 13 pin .156" molex female connector. Use a .156" molex male header pin as an adaptor between the original cable connectors and the newly made connector cables.  (Though some people will just cut off the original cables' connectors, and wire them directly to the new power supply, personally I prefer to make adaptors and to keep the original cabling intact.)

Cable layout:
5 pin cable: Use 1 foot each of black, white and green wire. The white wire will be in the middle (pin #3), and the black and green wires on the outside. See picture below for hook-up pin numbers.

13 pin cable: Use three 1 foot lengths of red wire (+12 volts), and four 1 foot lengths of black wire (ground). See picture below for hook-up pin numbers.

On the 13 pin housing, only 8 of these pins are used. Since I had some 8 pin housing laying around, i used that. But using a 13 pin connectors would be better.

I made the new cabling with the same color wires as the original cables which they will mate. This makes connection less confusing to the newbie. (See pictures below.)









On the switching video game power supply, add a 75 ohm 1/4 watt resistor between +5 volts and ground. Switching P.S. need "load" or they try and shut themselves down. Adding this resistor (though not always needed) will prevent this problem, since we aren't using the 5 volt supply.





To "mount" the new switching power supply, I used double-sided foam tape. Amazingly this works pretty well! Just mount the new power supply behind the DMD metal "can" on the floor of the head of the slot machine.



« Last Edit: July 05, 2020, 10:57:16 PM by knagl »
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! :)

Offline knagl

  • Kevin
  • NLG Site Administrator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2002
  • Reputation Power: 168
  • knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!knagl Is an-NLG GOD!
  • Gender: Male
Re: WMS Model 40x Dotmation Upper Power Supply Fix
« Reply #1 on: July 05, 2020, 10:37:09 PM »
(Additional images, for archive purposes.)
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! :)

 

Cell Phone and Pad Mode

imode wap wap2

NLG Archives

Archives @ newlifegames.net Wayback Machine

Contact Us

NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442
If you find this site helpful, please consider becoming a Contributing NLG Member with a monthly subscription to help cover the cost of pizza, coffee, aspirin, hosting, and bandwidth.
Contributing Members: get unlimited personal messages, can save topics and replies as drafts,
can post to the Classified ads, get unlimited access to the downloads, and also get this minty badge:



**Subscription Link** (Click Here) **Subscription Link**



           
If you would rather remain anonymous Thank You or just want to help support the site, please use this "make a donation" button:




From your entire NLG staff, thank you for supporting NLG.


New Life Games LLC 1788 HIGHWAY 95 UNIT 30 BULLHEAD CITY AZ 86442




Newlifegames.com     Newlifegames.net     Newlifegames.org

Newlifegame.com     Newlifegame.net     Newlifegame.org    Newlifegames.us

   New Life Games     NewLifeGames  NLG

 We Bring new Life to old Games    1-888-NLG-SLOTS

Are all Copyright and Trademarks of New Life Games LLC 1992 - 2022


FAIR USE NOTICE:



This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml
If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.




The NewLifeGames.com website is optimized for use with Firefox and a minimum screen resolution of 1600 x 900 pixels.

SimplePortal 2.3.5 © 2008-2012, SimplePortal