New Life Games LLC
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length

News:

Welcome to the NewLifeGames.com message forum! 

 


NLG Site Navigation Menu


Archives of old posts can be found at...... Newlifegames.net/nlg/

Author Topic: IGT S+ Newbie Code 61 Woes  (Read 6904 times)

0 Members and 1 Guest are viewing this topic.

Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #40 on: April 01, 2022, 02:54:11 AM »
Since the door optic bypass with the switch installed is not working on my S+ machine, would these S2000 optics work?
« Last Edit: April 01, 2022, 04:10:29 PM by Eggboat »

Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #41 on: April 12, 2022, 03:42:04 PM »
***** NEW OPTIC SENSORS INSTALLED UPDATE *****

Installed the new door optic sensors after breaking the wire off the last one. I performed the clear chip process again and the red dome light flashes only. Reinstalled the gaming chip. The red dome and white light begin flashing. Pressed reset button for 10+ seconds and 61-1 illuminates  along with an audible beep. Closed the door and turned the jackpot key and nothing but 61-1.

Took out cell phone camera and cannot see red IR light on the sensors. Any suggestions what to diagnose next?

Offline therockinelvis

  • Capes are not just for Super Hero's
  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2579
  • Reputation Power: 173
  • therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #42 on: April 12, 2022, 04:24:02 PM »
Are they aligned? Is the cashbox door switch wired together? Did you place tape on cabinet side and make a mark where the optic is? And do the same on door side? Close and latch the door. Do the 2 marks line up? You can also remove the reel glass to look directly at optics for aligning.
Thank Ya Thank Ya Very Much.

the rockin elvis

Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #43 on: April 12, 2022, 05:44:05 PM »
Yes, I used painters tape to align the optics so when the door closes it should line up with the lever down. I posted a photo of the cashbox switch and a member stated it looked correct.

Offline jay

  • Global NLG Site Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2122
  • Reputation Power: 164
  • jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!jay Is an-NLG GOD!
  • Gender: Male
  • The only way to beat the casino is to own it.
Re: IGT S+ Newbie Code 61 Woes
« Reply #44 on: April 12, 2022, 05:54:31 PM »
You should not need to run the clear chip through each time.

If your not seeing an image with your cell - and you will only see if from the emitter.... and it will be just a little spot flickering not some great big bright light ......
I would check the voltage (using a multimeter) to the emitter. Make sure your getting power.
Not sure if you have checked your fuses through this process ? this is a long shot.

Your symptoms all point to a door open condition. Typically caused by door open, or cash can door open.

Do you have an alternate game chip of any kind ? - just trying to rule out any other kind of funny behavior.
If you can't afford to lose you can't afford to win.

If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! :)

Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #45 on: April 12, 2022, 06:03:56 PM »
I will revisit your suggestions tomorrow when I get back from work and report back the results.

Super Appreciate the continued support from yall!

Offline Stayouttadabunker

  • Topic Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 5424
  • Reputation Power: 404
  • Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #46 on: April 12, 2022, 06:14:44 PM »
I think you blew up the optics on the MPU around your Reply #23 when you decided to try to use some unknown optics.
It may have drawn too many amps thru MPU IC components and could be why this board will not see the door closed.
You may need a spare MPU.
Remember, the more you tell us - the better we can help you!

Consider becoming a regular contributing member, which helps pay costs to keep this site up and running so you can keep your machine up and running :)

Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #47 on: April 15, 2022, 02:58:14 PM »
***** VOLAGE CHECK & ALIGNMENT CHECK UPDATE *****

Had a chance to revisit the machine after work today and checked the voltage on both emitter and receiver and both showed voltage. Then double checked my optics alignment, moved the inside sensor up a very little. Pressed and held the reset for 10+ seconds, closed the boor, turned the jackpot key and it went to 65-1. Opened it up, pressed the reset button again, closed the door and turned the jackpot key and it turned to 0 coins played and it did a test spin. Coins still falling through and not registering a credit with the coin comparator.

Now I am at a red flashing light and insert coin light is lit. Not sure what th check next, should I take a closer photo of the cash box bypass to confirm it was done correctly?

All of the fuses check OK visually and with a continuity meter check.

Unfortunately I don't have a spare gaming chip to try unless someone on the board has one for me to obtain.

Offline Tilt

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 4398
  • Reputation Power: 384
  • Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!
  • Gender: Male
Re: IGT S+ Newbie Code 61 Woes
« Reply #48 on: April 15, 2022, 03:19:57 PM »
Try changing the sample coin and if that doesn't work turn the sensitivity pot counter-clockwise.  If the insert coin light is lit the machine is ready for play.  The blinking red light will extinguish once you've successfully played a game.


Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #49 on: April 15, 2022, 03:31:21 PM »
Insert coin light lamp is lit.

Tried switching coin, had a brand new quarter and older washington quarter as my sample coin and coin still falls trough, turned sensitivity all the way counter clockwise and coins still fall through. It was mentioned to me earlier here the green LED light the the coin comparator doesn't need to be illuminated but I've seen some Youtube videos where it was lit green.

I also blew air through the coin optics below the comparator and no luck with that. Pressed the coin credit test button and that functions play.

Offline hotlsot

  • Contributing NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 608
  • Reputation Power: 62
  • hotlsot Is a rising star!hotlsot Is a rising star!hotlsot Is a rising star!hotlsot Is a rising star!hotlsot Is a rising star!hotlsot Is a rising star!
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #50 on: April 15, 2022, 03:45:32 PM »
test for continuity on your coin comparitor harness. Just from where it plugs into your cc and back to the main harness, about 6 inches from the cc. I still think you have an bad coin comparitor. The cap on the board goes bad, it's a 220uf 35v. Or just buy one, make sure you get the right voltage.

Offline Tilt

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 4398
  • Reputation Power: 384
  • Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!Tilt Is an-NLG GOD!
  • Gender: Male
Re: IGT S+ Newbie Code 61 Woes
« Reply #51 on: April 15, 2022, 03:53:42 PM »
The LED won't be illuminated with the door open.  I think hotlsot is right, you may have a bad comparitor or the wrong comparitor installed.  You can tie the rake on the comparitor for now if you want to test the rest of the machine.  It will accept anything that will fit down the chute that way.


Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #52 on: April 15, 2022, 03:57:54 PM »
I tested the black wire loomed cable/harness adapter containing the black, yellow and purple wire with the red jumper wire at the end and all tests good for continuity.

Attached is a photo of what I have. Whats interesting is the bracket that holds the comparator has 5¢ written on it with a sharpie. Not sure is the bracket and comparator came together by the previous owner or if it was original, the faded glass sticker states 25¢. I put a nickel into the comparitor and tried to play it and it just falls through like the quarters.

How do I perform the tie the rake procedure?
« Last Edit: April 15, 2022, 05:42:40 PM by Eggboat »

Offline therockinelvis

  • Capes are not just for Super Hero's
  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2579
  • Reputation Power: 173
  • therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #53 on: April 15, 2022, 05:15:16 PM »
Have you pushed the tiny white button just under the coin comp.? It should add a credit for each push to the max. coins. You should be able to press spin reels and play a psuedo game. With the coin comp. removed you should see a solenoid that moves the rake. Wire it so all coins go to hopper
Thank Ya Thank Ya Very Much.

the rockin elvis

Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #54 on: April 15, 2022, 05:40:21 PM »
I am able to press the tiny white button under the coin comp and I do get up to three credits and it does allow me to play it but after that the red light still remains blinking and the quarters still fall through. I do not hear or see any solenoid movement at all.

I tried the popsicle test and it never triggered the optics through the 10-1, 11-1 and 12-1 tests. So I took the coin bracket assembly off and split the coin optics apart, I found some lint and what looked like some sticker/crumbled paper inside and I also blew out the holes with air, put it all back and still the same thing results.

Offline Stayouttadabunker

  • Topic Moderator
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 5424
  • Reputation Power: 404
  • Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!Stayouttadabunker Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #55 on: April 15, 2022, 05:52:19 PM »
Eggboat,
Do you see these 2 screws I've encircled in green?
Remove them, take off the rake, the magnet, and pull the gray plug out of the front top of the coin comparitor.
Your machine will accept coins once you do what members are telling you to do.
Remember, the more you tell us - the better we can help you!

Consider becoming a regular contributing member, which helps pay costs to keep this site up and running so you can keep your machine up and running :)

Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #56 on: April 15, 2022, 06:06:01 PM »
Pulled off the rake/magnet. Unplugged the gray wire. Reinstalled the coin comparator and closed it up. Dropped a coin into it and it went to the hopper. Code 21 now appears and the white dome light is not blinking.

Offline therockinelvis

  • Capes are not just for Super Hero's
  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2579
  • Reputation Power: 173
  • therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #57 on: April 15, 2022, 06:15:10 PM »
Open, the close and latch the door a few times to clear 21. Since your optic test did not work, I would think you need new optics. Check with Jim. If your BV is working have fun playing. If you did a clear, make sure to use set chip to turn on BV and set denom.
Thank Ya Thank Ya Very Much.

the rockin elvis

Offline Eggboat

  • New NLG Member 3 to 100 Posts
  • **
  • Posts: 37
  • Reputation Power: 2
  • Eggboat New User has no influence.
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #58 on: April 15, 2022, 06:21:32 PM »
Opened and closed the door a few times and the code 21 still appears, also flipped the inside power switch on and off and still code 21.

I have the BV set chip but no clue on how to set it up to get it working. My BV has never made any noises since I got the machine and the lights where the the bill insert is does not light up at all but could be the bulbs.

Offline therockinelvis

  • Capes are not just for Super Hero's
  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 2579
  • Reputation Power: 173
  • therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!therockinelvis Is an-NLG GOD!
  • Gender: Male
  • NLG
Re: IGT S+ Newbie Code 61 Woes
« Reply #59 on: April 15, 2022, 06:31:07 PM »
It should cycle. Power supply most likely bad. Going to guess that you have a dbv145 or 200. If you can't clear 21 with door lat,,then it will need a clear
Thank Ya Thank Ya Very Much.

the rockin elvis

 

Cell Phone and Pad Mode

imode wap wap2

NLG Archives

Archives @ newlifegames.net Wayback Machine

Contact Us

NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442
If you find this site helpful, please consider becoming a Contributing NLG Member with a monthly subscription to help cover the cost of pizza, coffee, aspirin, hosting, and bandwidth.
Contributing Members: get unlimited personal messages, can save topics and replies as drafts,
can post to the Classified ads, get unlimited access to the downloads, and also get this minty badge:



**Subscription Link** (Click Here) **Subscription Link**



           
If you would rather remain anonymous Thank You or just want to help support the site, please use this "make a donation" button:




From your entire NLG staff, thank you for supporting NLG.


New Life Games LLC 1788 HIGHWAY 95 UNIT 30 BULLHEAD CITY AZ 86442




Newlifegames.com     Newlifegames.net     Newlifegames.org

Newlifegame.com     Newlifegame.net     Newlifegame.org    Newlifegames.us

   New Life Games     NewLifeGames  NLG

 We Bring new Life to old Games    1-888-NLG-SLOTS

Are all Copyright and Trademarks of New Life Games LLC 1992 - 2022


FAIR USE NOTICE:



This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml
If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.




The NewLifeGames.com website is optimized for use with Firefox and a minimum screen resolution of 1600 x 900 pixels.

SimplePortal 2.3.5 © 2008-2012, SimplePortal