New Life Games LLC
Bill Validators, Currency Acceptors and Printers => JCM WBA 10, 11, 12, 13, 14, 20, 21, 22, and 23 Bill Validators => Topic started by: erbarr1 on May 19, 2023, 06:31:04 PM
-
Hello good people,
I have a 1997 SP and the BV will not operate.
1. New power supply. Plug n play.
2. Two red lights are on by the dips.
3. Ran Setup 123, good.
4. Duck bill will only light up when dip#8 in on. (They were all ‘off’ before)
Still no cycling of the BV and not accepting any bills. I do have an extra WBA 12 but the cables are different.
Any, any help would be greatly appreciated!!
Thx Eddie
-
I also ran the dip switch test and both the head and transport function.
-
Can you post pictures of your machine and the underside of the WBA
-
Thx for taking interest.
-
Is the yellow bezel light lit up on the outside of the door? Can you post a picture of the dip switches on the BV.? Have you enabled the BV with the Set chip?
-
Bezel light on when dip switch 8 is ON. Besides that they are all off. RAN SETUP 123.
-
When I ran the dip test the BV seemed to function. Some of the switches tested sensors but I don’t know what to look for on these tests.
-
Try using a set15 set chip to set denom and activate BV (9_1). IVC123 is a clear chip.
-
I don’t have a SET15 chip but I do have the IVC123.
-
Should I run the IVC123 then the SETUP 123?
-
What is a setup 123? Does it allow you to set denom and enable the BV? (9-1) You should not need to clear unless in a 61 loop.
-
Setup 123 is supposed to set up the BV from what I’ve gathered.
-
SORRY WRONG CHIP NUMBER. Set015 was what I used. Just ran it again, no movement from the BV.
I must of mistaken it with the IVC123.
-
Ok, ran the set015 again and now I actually hear the BV turn on. The dips are all set on off. Outside bill light is off, (duck bill?). No noise or movement when I try to insert a bill. Now if I put the dip #8 on ON, the duck bill lights up and blinks. Try to insert bill, still nothing…..?
-
Leave all dips in off position. When you used SET015 you set it to 91 and set the denomination at the same time? 25 cent. Didn't leave denom set at 0?
-
They were all off when I ran the set015. Set denomination at 5 cents.
-
They were all off when I ran the set015. Set denomination at 5 cents.
Did you change the 9_0 to 9_1 to enable the BV?
-
Yes, like I said went to the whole process.
-
It does have movement at startup but no light and won’t accept any bills.
-
Cashbox is right side up? Cashbox door is staying closed ? Has the cashbox door switch been jumpered out?
-
Yes, yes and yes.
-
Swap the scanner head from your WBA 12
-
Thanks, I’ll try that today!!
-
Ok
1. Replaced the wba11 head with a wba12 , cycles but the duck bill still doesn’t light up and still doesn’t accept bills.
2. Ran set015, same issues.
3. Installed harness to go from wba11 to wba12 complete with transport. Ran set015, same results, cycles but no light.
4. Also did the dip test.
Could a cap/resistor/diode be bad on the motherboard?
That feeling of ignorance is an ugly realization.
-
What is your credit limit set at?
-
I don’t know. Where would you set that?
-
appears that you have been able to accomplish a few things and understand the menus and test menus. here is an INVALUABLE guide that actually tells you what all those numbers mean and what you are setting. Using these cards you can test every switch, light bulb, and function of the s plus machine.
coins played number 7 is where you set the limits,
https://newlifegames.com/nlg/index.php?topic=18866.0
hope this helps
Jim
-
Thx Jim, I’ll give it a shot!