New Life Games LLC

**Reel Slots** Gaming Machines => IGT S2000 and Vision Games => Topic started by: vegasbaby on February 28, 2015, 04:24:03 PM

Title: S2000 5 REEL TO 3 REEL CONVERSION what i/o boards
Post by: vegasbaby on February 28, 2015, 04:24:03 PM

Hi

In the middle of a 5 reel to 3 reel conversion,can some one tell me what I/O BOARDS are needed for door & cabinet. I believe 801 for door,but what about cabinet. Also i changed the back lit controller board from 5 reel to 3 reel type,how many connections are made to the 3 reel board,i have two plugged in now,but have this 4 wire plug with out a home,see pictures.
THANKS FOR ALL THE HELP.
MARK

Title: Re: S2000 5 REEL TO 3 REEL CONVERSION what i/o boards
Post by: RB on February 28, 2015, 04:42:30 PM

That's the power for your controller. Usually goes on top left but since yours is installed upside down it goes lower right to the open connector in your pic. Cabinet I/O remains unchanged, 801 for the door is correct.

Title: Re: S2000 5 REEL TO 3 REEL CONVERSION what i/o boards
Post by: vegasbaby on February 28, 2015, 06:29:21 PM

Thanks

I turned the back lit controller board around,all is good there. But have a few more last connections that need a home or landing place to connect.
#1 the 5 reel deck has a closed end plug,that had a plug,is that what i use on the 3 reel deck,as it has the same ?
#2 The 5 credit lite box,what plugs in there?
#3 The black in white plug,where might i finds its connection point.
#4 And credit box has two connections,but i only have one installed?

And do recommend cutting the metal bracket that supports vfd & glass

THANKS
MARK

Title: Re: S2000 5 REEL TO 3 REEL CONVERSION what i/o boards
Post by: RB on February 28, 2015, 07:52:56 PM

1 The coin bypass plug (pic2) needs to be transferred to you other harness. 

2 There should be a black flat connector in your harness inside the door that connects to the light box. It has 5 brown wires & 1 red. It's probably zip tied.

3 The black & white connectors (pic 4) go inside the cabinet behind the first reel. You should have disconnected your other harness there. Those are for the door optic & BV bezel light.

4 The other connector on the credit panel goes to the denom light box that is missing from your setup. I would not cut the display bracket but would try to find the correct one or even better a long reel glass.

I might add that the I/O in your picture is no longer needed & your wires that are plugged in to it at the top should go inside the door to a 801. Those other wires pictured are for the fluorescent ballast inside the door, green ground.

Title: Re: S2000 5 REEL TO 3 REEL CONVERSION what i/o boards
Post by: vegasbaby on February 28, 2015, 09:37:58 PM

THANKS RON
Made the changes,but want to make sure, i fully under stand door I/O wire are not needed,just tuck them into door. I did move the door I/O to area like in your pictures.
THANKS
MARK

Title: Re: S2000 5 REEL TO 3 REEL CONVERSION what i/o boards
Post by: RB on February 28, 2015, 09:52:17 PM

Mark,
you can remove the additional I/O bracket & wiring. It's only needed if you want to go back to a dual row button panel.

Title: Re: S2000 5 REEL TO 3 REEL CONVERSION what i/o boards
Post by: vegasbaby on March 01, 2015, 02:14:58 PM

HI

I got all the connections made. Since I'm  changing games going from multi    denomination set up to 25 cent, i under stand i must clear first with a 97. Is that correct ?
Also i have a clear chip,but it just says CLEAR CHIP no number markings,if i don't know what number it it is,would it be best to order one?

THANKS AGAIN FOR THE HELP

MARK

Title: Re: S2000 5 REEL TO 3 REEL CONVERSION what i/o boards
Post by: foster on March 01, 2015, 02:28:07 PM

no need to clear as long as your accounting denom is $0.01
only enable one player denom set to $0.25