New Life Games LLC
**Reel Slots** Gaming Machines => IGT S2000 and Vision Games => Topic started by: DP on April 16, 2020, 07:31:23 PM
-
Hello,
I have a ton of step by step directions on how to change my Denomination and set the pay off to the highest setting, I now have set of Keys/Chips and I have tried every combination of all these. Can someone look over these and see the chips I have and send me a good step by step directions PLEASE. I hope I did not mess anything. This is what everyone has sent me.
1. Power off slot and remove MPU tray
2. Remove SB chip and replace it with CLEAR chip
3. Power on slot and wait for top two amber lights to lite up
4. Power off slot and remove CLEAR chip and reinsert SB chip
5. Leave door open and power on slot
6. Should read “TESTING MEMORY†then alarm sounds with message error “RAM ERRORâ€
7. Turn RESET key four(4) times and it should read “PRESS TEST SWITCH FOR 2-3 SECONDSâ€
8. Hold MPU white button and release
9. LED now reads “CLOSE MAIN DOOR†Close main door completely
10. LED now should read “TESTING MEMORY†and when finished you get “CALL ATTENDENT†Message
11. Open main door and alarm should sound
12. Turn reset key 3 times
13. LED should read “MACHINE TYPE MISMATCHâ€
14. Power off slot and remove MPU and SB chip
15. Insert KEY chip
16. Power on slot and wait for two amber lights to come on
17. Power off slot—remove KEY chip—insert SB chip
18. Power on slot with door open and LED should read “7 KEY CHIP CONFIGâ€
BASIC CONFIG SETUP
Button Usage:
1. SERVICE and CASH OUT buttons control up and down in menus (sometimes sideways too)
EXAMPLE: 7.1, 7.1, 7.3—will scroll through these
2. SPIN button cycles through options horizontally
EXAMPLE: 7.1---7.1.1---7.1.1.1
3. MAX BET button confirms and backs out of menu horizontally—like a backspace
Multi Denomination Setup—Must be done in this order
7.1.1.1 Accounting—Usually lowest used value—Set $.01
Use MAX BET to set and confirm—Cannot be reset without doing a CLEAR
7.1.1.2 Coin Denomination—Value of coin dropped—Set $.01
Use MAX BET to set and confirm—Cannot be reset without doing a CLEAR
7.1.1.3 Player Denomination—Value assigned to each player
Use SERVICE and CASH OUT buttons to set amount for each player
7.1.2 Game Selection—Assigns % pay to each player
7.1.1.4 Touch Panel—Assign player number to touch button (Not available for single denomination)
7.1.6 Machine Types—Upright
7.1.7 Token Payout—Use printer and not Hopper—DISABLE
7.2.2 Printer-ENABLE
Set the following if you are using a TITO
7.1.3.5 SYSTEM BONUS---LEGACY
7.1.5 SAS AFT Controller
7.2.1.1 SAS Validation Type—System Mode
7.2.1.2 Validation Security—ENABLED
7.2.1.4 HandPay Validation—Don’t validate handpay receipt
7.2.3.1 Voucher Redemption—SAS
7.2.3.2 Voucher Limit Follows Credit Limit
7.2.3.3 Change Voucher--ENABLED
7.2.4.1 Remote Handpay Reset Enabled
7.2.5 Coinless Mode—DISABLED
Close door and machine boots up—Open door and press white TEST BUTTON
3.1.4 Field Locked in coinless mode—set LIMITS
Hopper Limit---“0†Only if no hopper is installed and in coin mode
Credit Limit—10000
Jackpot Limit—10000
Bill Limit—3000
Set the following if you are using a TITO (Set in this order)
3.4.2.2 Bally Miser Channel—OFF (MUST BE DONE FIRST)
3.1.9 Serial Number (any number)
3.4.1.1.1 SAS Address—001
3.4.1.1.2 SAS Channel—3 (Bally Miser must to OFF to Set)
3.4.1.1.3 Primary Link Down—Game Enabled
3.4.1.1.4 Primary Hand Pay--Hand Pay Reporting Disabled
3.4.1.4 AFT Asset Number—1
3.4.1.3 Cashless-Primary * Progressive-Secondary * Legacy Bonus-Primary * ASDC-Secondary
Link Bonus –Secondary * Validation-Primary
If you plan to key chip again you must make sure machine has “0†credits on it
You have an Enhanced board, so you do need to keep the Varta battery. Key 45 is what you need to get your machine going again. You cleared it with your 224 clear. Don't know who sent you a 24 key chip. IGT has 17, 22, 31 and 45 key chips[/font]
DP, your enhanced MPU uses a R board. The correct key chip is RBK00001. It performs clear & key functions. You can remove the Varta battery (recommended) but you must also remove the component at U16 or at least clip the 3 pins so it doesn't make contact. Therockinelvis is unintentionally steering you wrong. PM me if you need a key chip.[/font]
DP :Scratch-Head:
-
PM sent.
-
You have a R board game you clear and key with the rbk chip.
Turn off the machine. Remove the boot chip (not the SB) and replace with the rbk chip and power up.
The rest should be as described above.
-
More info
"Remove the boot chip and install the RBK00001 chip. Power it up.
Instead of waiting for the amber lights to come on, go to the screen menu, select Key Chip, "Apply Key Chip". It'll say 'Spin Reels to apply Key Chip'. ..."Key Chip Applied".
Be sure to select 'RAM Options' / "Clear RAM" to avoid a 'Key Chip Access Failure', if you've saved before. (it worked for me anyway) Then 'Apply' the Key Chip.
Then power down and replace the Boot chip...
When you clear RAM, the alarm will go off at restart! Just turn the reset key about 4 times through the listed errors, then it will ask you to push/hold the reset button on the MPU/board for 2 seconds. You should end up with at "Key Chip" menu displayed... edit params from there.