New Life Games LLC

General NLG Chat => General Chat, Slot Shop **Tech Talk** Welcome wagon and other stuff. (Off-Topic Post Welcome) => Topic started by: brichter on December 08, 2017, 12:54:37 AM

Title: Back in it...
Post by: brichter on December 08, 2017, 12:54:37 AM
I fired up my S+ and Vision tonight, hadn't turned them on in 4-5 years. Work and life got in the way, and since I'm moving in a couple weeks or a month, I figured I'd better find out where I was at with them.

Had to replace batteries in both machines, lucky the Vision was a 500 board! I didn't need a replacement for the 3.6v battery that was growing hair on the main board, just unsoldered the old one and slid in a new CR2032, cleared the RAM errors, and away she went! The S+ was a bit tougher, had to solder in the new battery (after I finally found the one I bought 4 years ago and had put in a safe place so I wouldn't lose it!  :rotfl: ), but the progressive isn't working and it's throwing a C1, so it needs a new battery too!

It felt good to throw a few hundred credits on them and pull the handles a few times!  :applause:

10 Attaboys for the first responder that can tell me what's wrong with this picture!  :Scratch-Head: :Crazy:
Title: Re: Back in it...
Post by: qbert on December 08, 2017, 05:01:58 AM
There are no ear speakers on the vision machine and there does not appear to be any way to change the denomination on it although it is set up for 5 or 10 cent play. Sticker says 25 cents.
Title: Re: Back in it...
Post by: Shaggy on December 08, 2017, 06:29:03 AM
Sticker also says play 2 coins. 3 coins played in the display. Looks like play 2 credits on the large button.
Title: Re: Back in it...
Post by: Jim on December 08, 2017, 08:27:33 AM
other than what was mentioned above, the progressive number looks different, and the reels in the vision look different,  looks like the red seven reel is from a chainsaw and toasters reel set ???

the original vision series machine did not have "ear type speakers"  they were built in to the same strip as the molding. there was a grill and some sort of plastic funnel that sent the sound out to the player.

Jim
Title: Re: Back in it...
Post by: brichter on December 08, 2017, 01:54:54 PM
There are no ear speakers on the vision machine and there does not appear to be any way to change the denomination on it although it is set up for 5 or 10 cent play. Sticker says 25 cents.

Visions did not come with ear speakers, those were on the S2000. I looked into upgrading these, but there's a lot of work to be done to retrofit.

You're correct about the denomination, I don't have a $ .05 denomination sticker yet. :cool_thumb_up: 5 Attaboys for you, sir!

There's a bigger issue than that, though...   :Crazy:
Title: Re: Back in it...
Post by: brichter on December 08, 2017, 02:08:23 PM
other than what was mentioned above, the progressive number looks different, and the reels in the vision look different,  looks like the red seven reel is from a chainsaw and toasters reel set ???

the original vision series machine did not have "ear type speakers"  they were built in to the same strip as the molding. there was a grill and some sort of plastic funnel that sent the sound out to the player.

Jim

DING DING DING! We have a winner! They are indeed the wrong reel strips in the Vision game, those are my C&T strips. The DD strips are visible on top of the Vision cabinet.

The issue with the progressive is due to the dead battery mentioned above, I need to get a new battery ordered so I can set it up.

10 Attaboys for you, and 5 Attaboys each for qbert and Shaggy for noticing the denomination and coin issues! I actually have a "Play 3 coins" label around here somewhere, hopefully I find then when I'm packing before or unpacking after the move. I swapped the "Play x Coins" buttons last night before going to bed, so they are correct now.

I also have a couple Mikhon Supreme displays (a 1x3 and a 2x3) and a Con2 that I will try to use to drive them once I get everything set up after the move. All this stuff is slowly starting to come back to me... :cool_thumb_up:
Title: Re: Back in it...
Post by: Tilt on December 08, 2017, 02:21:29 PM
If you have a CHAMII+ progressive controller it has a rechargeable battery soldered onto the controller board.  You just need to leave it turned on for awhile to recharge it and then reprogram it.
Title: Re: Back in it...
Post by: brichter on December 08, 2017, 04:30:16 PM
If you have a CHAMII+ progressive controller it has a rechargeable battery soldered onto the controller board.  You just need to leave it turned on for awhile to recharge it and then reprogram it.

That's what I thought as well... but it's been on for 4 days and still loses everything when I power it off. I may have killed it by leaving it off for so long.  :fryingpan:
Title: Re: Back in it...
Post by: qbert on December 08, 2017, 05:23:55 PM
Replace that Panasonic rechargeable battery on the chamii.
I found after I did this the machine will hold it's memory for months. Before that it wouldn't last two weeks without losing everything.
Rich
Title: Re: Back in it...
Post by: Tilt on December 08, 2017, 08:24:32 PM
Mouser P/N 658-VL2020/VCN

https://www.mouser.com/Search/ProductDetail.aspx?R=VL-2020%2fVCNvirtualkey65800000virtualkey658-VL2020%2fVCN (https://www.mouser.com/Search/ProductDetail.aspx?R=VL-2020%2fVCNvirtualkey65800000virtualkey658-VL2020%2fVCN)
Title: Re: Back in it...
Post by: brichter on December 09, 2017, 10:37:51 AM
Replace that Panasonic rechargeable battery on the chamii.
I found after I did this the machine will hold it's memory for months. Before that it wouldn't last two weeks without losing everything.
Rich


Yup,that's been my experience as well.
Title: Re: Back in it...
Post by: brichter on December 09, 2017, 10:54:57 AM
Mouser P/N 658-VL2020/VCN

https://www.mouser.com/Search/ProductDetail.aspx?R=VL-2020%2fVCNvirtualkey65800000virtualkey658-VL2020%2fVCN (https://www.mouser.com/Search/ProductDetail.aspx?R=VL-2020%2fVCNvirtualkey65800000virtualkey658-VL2020%2fVCN)

What? I shouldn't get it from Happ?  :rotfl: :rotfl: :rotfl:

Thanks for the legwork!  :cool_thumb_up:
Title: Re: Back in it...
Post by: Tilt on December 09, 2017, 11:35:40 AM
Mouser P/N 658-VL2020/VCN

https://www.mouser.com/Search/ProductDetail.aspx?R=VL-2020%2fVCNvirtualkey65800000virtualkey658-VL2020%2fVCN (https://www.mouser.com/Search/ProductDetail.aspx?R=VL-2020%2fVCNvirtualkey65800000virtualkey658-VL2020%2fVCN)

What? I shouldn't get it from Happ?  :rotfl: :rotfl: :rotfl:

Thanks for the legwork!  :cool_thumb_up:

Not unless you want a couple of lifetime supplies of them.  The minimum order is $100 now and I think they still have their infamous mysterious shipping charges!
Title: Re: Back in it...
Post by: brichter on December 09, 2017, 11:57:52 AM
Mouser P/N 658-VL2020/VCN

https://www.mouser.com/Search/ProductDetail.aspx?R=VL-2020%2fVCNvirtualkey65800000virtualkey658-VL2020%2fVCN (https://www.mouser.com/Search/ProductDetail.aspx?R=VL-2020%2fVCNvirtualkey65800000virtualkey658-VL2020%2fVCN)

What? I shouldn't get it from Happ?  :rotfl: :rotfl: :rotfl:

Thanks for the legwork!  :cool_thumb_up:

Not unless you want a couple of lifetime supplies of them.  The minimum order is $100 now and I think they still have their infamous mysterious shipping charges!

Yes, I've fallen victim to their Mystery Shipping (or is that Haywire Shipping? :lol: :lol: ) before! I didn't know they had a $100 minimum now, though, just another reason to keep them off the supplier list.  :talktothehand:
SimplePortal 2.3.5 © 2008-2012, SimplePortal