New Life Games LLC

Bill Validators, Currency Acceptors and Printers => JCM DBV-45, DBV-145, and DBV-200 Bill Validators => Topic started by: cheller80 on January 03, 2021, 03:58:32 PM

Title: DBV-200 Connector Pin type?
Post by: cheller80 on January 03, 2021, 03:58:32 PM

Hi, getting intermittent problems due to a bad pin on the right side front 4-pin connector (the orange wire).


Anyone know what type those are?  Thanks!

Title: Re: DBV-200 Connector Pin type?
Post by: Stayouttadabunker on January 03, 2021, 04:28:50 PM

Picture of yours would help....there's different kinds....these are males for example.


The housing you have would tell me exactly what should go in there.

Title: Re: DBV-200 Connector Pin type?
Post by: cheller80 on January 03, 2021, 04:55:20 PM

Hi, it's your first pic, the long thin pin.  What type is that?

Title: Re: DBV-200 Connector Pin type?
Post by: Stayouttadabunker on January 03, 2021, 06:33:52 PM

It's an SL crimp terminal from the C-Grid family.

This is the canadian link...they have an American link as well...just take canada out of the link...lol...>>>

https://canada.newark.com/molex/16-02-0109/contact-pin-24awg-crimp/dp/74C3240 (https://canada.newark.com/molex/16-02-0109/contact-pin-24awg-crimp/dp/74C3240)


Here 's the data sheet....see if it's the same pins you're looking for or not...>>>

http://www.farnell.com/datasheets/2694248.pdf (http://www.farnell.com/datasheets/2694248.pdf)


I cannot be sure until you show me a photo of your housing. Need I ask you again?  :fryingpan: :Tongue_Out:
The more you tell me, the better I can help you.  :cool_thumb_up:

Title: Re: DBV-200 Connector Pin type?
Post by: cheller80 on January 03, 2021, 08:25:06 PM

Hi, think you've got it.  Sorry, was away from the game earlier, connector in pic, mate is behind it.


Thanks for your help!

Title: Re: DBV-200 Connector Pin type?
Post by: Stayouttadabunker on January 04, 2021, 05:38:54 AM

You may be able to salvage that pin....
There's a hole for each pin on one side of the housing.
Get something pointy and push the tab down a little then pull back on the pin with a needle-nosed pliers.
The pin should come right out the rear end of the AMP housing where the wires extrude.
Then try to spread the tabs on the pin with and Exacto knife and resolder the wire to the end of the pin.
If you tin the end of the broken wire with a little solder, it may be strong enough to hold the pin.
Spread the pin tab slightly upwards then push the pin back into the housing.

Title: Re: DBV-200 Connector Pin type?
Post by: cheller80 on January 04, 2021, 04:33:54 PM

Yes, will give solder a shot before ordering.  Thanks!

Title: Re: DBV-200 Connector Pin type?
Post by: Stayouttadabunker on January 04, 2021, 04:52:30 PM

Good luck!

Let us know how it turns out! :)

Title: Re: DBV-200 Connector Pin type?
Post by: cheller80 on January 05, 2021, 05:15:43 PM

Like the Exacto knife trick, hadn't thought of that before. Just was getting this about right when the 2nd wire popped out of its terminal.


Arghhh...


Just ordered some new ones to recrimp that connector...obviously it's time.  Thanks!

Title: Re: DBV-200 Connector Pin type?
Post by: Badbaud on January 05, 2021, 07:03:19 PM

Those are JST pins.