New Life Games LLC
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length

News:

Welcome to the NewLifeGames.com message forum! 

 


NLG Site Navigation Menu


Archives of old posts can be found at...... Newlifegames.net/nlg/

Author Topic: How to bench test your payboard  (Read 9688 times)

0 Members and 1 Guest are viewing this topic.

Offline OldReno

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 571
  • Reputation Power: 75
  • OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.
  • Gender: Male
  • NLG
How to bench test your payboard
« on: December 01, 2019, 07:45:13 PM »
with your VOM on ohms, clip one lead to the feed wire (93) on your pay board. Put other lead on 2 pay tab. Step board 2 steps, should go off. Next put on 5 pay, step 3 more steps should go off. 10 pay 5 more steps goes off. 14 pay 4 more steps. Etc, etc.
you can quickly check all tabs are contacting just by testing each one in zero position.
To test carry over (CO), step board up until you see it finally make contact. Outboard wipers should be adjusted to halfway through CO circuit then they should drop off.
« Last Edit: December 02, 2019, 09:51:05 AM by shortrackskater »
The real picture of the Face on Mars.

Offline SPN

  • NLG Member 251 to 500 Posts
  • ****
  • Posts: 309
  • Reputation Power: 26
  • SPN New User barely matters.SPN New User barely matters.
  • Gender: Male
  • NLG
Re: How to bench test your payboard
« Reply #1 on: October 29, 2020, 12:47:16 PM »



Hi


I’m trying to follow the steps to test and adjust my payboard on my 831 since I have some problems with my higher payouts 100 and up, it seems to over pay with around 10-15 coins..


I did understood the lover tests from 2-18 steps and so far it works as it should, but from there I’m not sure how to check and adjust the higher payout ..


I’m from Norway and maybe not quite understand how to adjust the wipers or the co circuit part..


I’m grateful for all the help thanks 🤗

Offline OldReno

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 571
  • Reputation Power: 75
  • OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.
  • Gender: Male
  • NLG
Re: How to bench test your payboard
« Reply #2 on: October 30, 2020, 03:49:20 PM »
Hi. Your higher pays are controlled by the 2 sets of outboard wipers - 50, 100 and 200 pay tabs. As the spiral cam winds up, it pulls those wipers off their tabs. The must stay on the tabs until your inboard spiral wipers get to the CO (carry over) portion of the inner board.
If the outboards break contact before then it will short pay.
If the outboards stay on too long, it will overpay.
It sounds like they are on too long, so loosen the 2 screws and adjust them so they come off outboard tabs sooner. They should come off when your inner wiper is about in the middle of the CO. Hope that helps, from a fellow (American) Norwegian
The real picture of the Face on Mars.

Offline SPN

  • NLG Member 251 to 500 Posts
  • ****
  • Posts: 309
  • Reputation Power: 26
  • SPN New User barely matters.SPN New User barely matters.
  • Gender: Male
  • NLG
Re: How to bench test your payboard
« Reply #3 on: October 30, 2020, 04:50:40 PM »



Hi and thanks for your reply about the higher payout issue.


I’m not sure I understand you correctly but I have a feeling that this are the two screws I must loosen up and adjust the wiper?


Is it the one I marked red or blue, or both? Or is IT something totally different ? (See the picture i attached)
















Offline OldReno

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 571
  • Reputation Power: 75
  • OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.
  • Gender: Male
  • NLG
Re: How to bench test your payboard
« Reply #4 on: October 30, 2020, 05:09:41 PM »
Yes. The red one is for your 100 pay, blue for 50 and 150. Good luck.
Once you loosen screws they slide to adjust. Right on.
The real picture of the Face on Mars.

Offline SPN

  • NLG Member 251 to 500 Posts
  • ****
  • Posts: 309
  • Reputation Power: 26
  • SPN New User barely matters.SPN New User barely matters.
  • Gender: Male
  • NLG
Re: How to bench test your payboard
« Reply #5 on: October 30, 2020, 05:20:18 PM »



I will try it out tomorrow since it’s past midnight here now and I will wake up the house if I start testing it now, hehe


I’m very thankful for your help and for the post about bench testing the payboard Sir.


Greetings from Norway 🇳🇴








Offline OldReno

  • Sr NLG Member
  • NLG Member 501 to 10,000 Posts
  • *
  • Posts: 571
  • Reputation Power: 75
  • OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.OldReno Has a powerful will.
  • Gender: Male
  • NLG
Re: How to bench test your payboard
« Reply #6 on: October 30, 2020, 05:48:46 PM »
My pleasure
The real picture of the Face on Mars.

Offline SPN

  • NLG Member 251 to 500 Posts
  • ****
  • Posts: 309
  • Reputation Power: 26
  • SPN New User barely matters.SPN New User barely matters.
  • Gender: Male
  • NLG
Re: How to bench test your payboard
« Reply #7 on: October 31, 2020, 03:24:18 AM »


I finally made it thanks to you, and now all pay outs are correctly and even the inn out meters counts correctly.


 :thank_you:

 

Cell Phone and Pad Mode

imode wap wap2

NLG Archives

Archives @ newlifegames.net Wayback Machine

Contact Us

NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442
If you find this site helpful, please consider becoming a Contributing NLG Member with a monthly subscription to help cover the cost of pizza, coffee, aspirin, hosting, and bandwidth.
Contributing Members: get unlimited personal messages, can save topics and replies as drafts,
can post to the Classified ads, get unlimited access to the downloads, and also get this minty badge:



**Subscription Link** (Click Here) **Subscription Link**



           
If you would rather remain anonymous Thank You or just want to help support the site, please use this "make a donation" button:




From your entire NLG staff, thank you for supporting NLG.


New Life Games LLC 1788 HIGHWAY 95 UNIT 30 BULLHEAD CITY AZ 86442




Newlifegames.com     Newlifegames.net     Newlifegames.org

Newlifegame.com     Newlifegame.net     Newlifegame.org    Newlifegames.us

   New Life Games     NewLifeGames  NLG

 We Bring new Life to old Games    1-888-NLG-SLOTS

Are all Copyright and Trademarks of New Life Games LLC 1992 - 2022


FAIR USE NOTICE:



This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml
If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.




The NewLifeGames.com website is optimized for use with Firefox and a minimum screen resolution of 1600 x 900 pixels.

SimplePortal 2.3.5 © 2008-2012, SimplePortal