New Life Games LLC

**Reel Slots** Gaming Machines => IGT S2000 and Vision Games => Topic started by: Pinkodoc6420 on May 21, 2022, 03:12:16 PM

Title: S2000 Finally Working But Won't Play
Post by: Pinkodoc6420 on May 21, 2022, 03:12:16 PM

 :banghead:
 I posted about the all too common battery issue, I ordered and replaced the battery which brought the machine back to life. Now I can put money in it and the screen shows everything correctly, the screen shows Play 75 Credits (it's a 2¢ machine) so I put 8$ in it, the spin and max bet buttons flash, but pushing them does nothing. Cannot for the life of me get the game to actually play. I took a short video showing this, anyone able to help!?

https://youtube.com/shorts/DYZFp_Iv3YM?feature=share

Title: Re: S2000 Finally Working But Won't Play
Post by: Pinkodoc6420 on May 21, 2022, 05:11:26 PM

Here's another video showing more ...
https://youtu.be/MJBw69MvGuQ

Title: Re: S2000 Finally Working But Won't Play
Post by: sixcardmark on May 21, 2022, 05:27:57 PM

Buttons should not be blinking.  Turn machine off and reseat the MPU and boot it back up.  Maybe check for a bent pin going to backplane while you have it out.

Title: Re: S2000 Finally Working But Won't Play
Post by: Retro tech repair on May 21, 2022, 05:31:08 PM

Looks like only some of the buttons are blinking the standard door io card is not working properly. The one on the 45 degree angle.

Title: Re: S2000 Finally Working But Won't Play
Post by: RB on May 21, 2022, 05:34:21 PM

Check all of the door I/O related connections and verify that you do not have a hot button wire (red) grounding out underneath the button panel.

Title: Re: S2000 Finally Working But Won't Play
Post by: Pinkodoc6420 on May 21, 2022, 05:45:53 PM

Quote from: sixcardmark on May 21, 2022, 05:27:57 PM

Buttons should not be blinking.  Turn machine off and reseat the MPU and boot it back up.  Maybe check for a bent pin going to backplane while you have it out.

How do I do the reset?

Title: Re: S2000 Finally Working But Won't Play
Post by: Pinkodoc6420 on May 21, 2022, 05:46:26 PM

Quote from: Retro tech repair on May 21, 2022, 05:31:08 PM

Looks like only some of the buttons are blinking the standard door io card is not working properly. The one on the 45 degree angle.

What would you suggest I do about that? All the buttons register when doing the I/O input test...

Title: Re: S2000 Finally Working But Won't Play
Post by: Pinkodoc6420 on May 21, 2022, 05:46:59 PM

Quote from: RB on May 21, 2022, 05:34:21 PM

Check all of the door I/O related connections and verify that you do not have a hot button wire (red) grounding out underneath the button panel.

I looked at everything as best I could but I'll go back over it again tomorrow

Title: Re: S2000 Finally Working But Won't Play
Post by: Stayouttadabunker on May 23, 2022, 04:31:17 AM

Quote from: Pinkodoc6420 on May 21, 2022, 05:45:53 PM

Quote from: sixcardmark on May 21, 2022, 05:27:57 PM

Buttons should not be blinking.  Turn machine off and reseat the MPU and boot it back up.  Maybe check for a bent pin going to backplane while you have it out.

How do I do the reset?

Reseat....he means to physically pull out the MPU board, visually inspect the all the pins for straightness, then manually re-install the MPU fully back onto the pins.

Title: Re: S2000 Finally Working But Won't Play
Post by: Pinkodoc6420 on May 23, 2022, 07:51:07 AM

Did that a few times no, no luck. I swapped the two I/o boards around with no luck and now I have a ten pin I/o card not found error. Thinking I might need to order a replacement for the one at a 45 degree angle?

Title: Re: S2000 Finally Working But Won't Play
Post by: RB on May 23, 2022, 10:06:59 AM

10 button I/O not found usually means you did not plug them back in correctly. Are both cards the same? If so swap the two top connectors.

Title: Re: S2000 Finally Working But Won't Play
Post by: Pinkodoc6420 on May 23, 2022, 11:07:35 AM

 Ill double check and try that when I get home.