New Life Games LLC
**Reel Slots** Gaming Machines => Bally Reel Games => Topic started by: mwade109 on January 16, 2021, 07:52:29 PM
-
Ok, I got this machine the way most people seem to get the 5000+'s, broken & cheap. Replaced the battery, want to do a complete ramclear to see where it gets me before I go shelling out 60 bucks for what appears to be the only place that sells a homemade pin pad to complete the setup. If I turn on the machine I get the loud alarm and a 5.0 in the Win and F in Last In and 0 in Coin In. When I close the door I get two dots in the Win, 5535 in the Paid and still the F0 in the ones below. (Attaching pics)
I read somewhere here to simply pop out the top board to somehow force it into a ram clear. When I pull that board out a bit, the machine powers on but no action whatsoever, nothing in the displays just darkness and disappointment.
So I go ahead and order the clear chips, I do ahead and take out the piggybacked board, replace the chips with the clear chips, the instructions at that point don't actually say to put the piggyback board back on or not before inserting the board but either way, I never get anything in the displays (yes I tried it both ways).
I never got a ch or cl.
Any ideas before I start parting out the cabinet items and glass on eBay?
(please respond here as even tho I have donated a couple time here (not much, I'm poor)), I'm still limited to 10 emails in my mailbox and that fills pretty quickly.
Thanks
-
Nobody can help with this?
(sorry, no matter what I do the pic gets sideways after I upload it)
-
Was hoping that this would be helpful, as I to have managed to aquire 3 of the 5000+ machines.
I'll start working on them one day.
Have you searched around in the forum's section for the procedures? I downloaded the clear instructions posted above, but in English from there. So I know your clear procedure is listed there somewhere.
Good luck.
Curtis ash100
-
Bally 5000 - RAM CLEAR PROCEDURES
Method 1
Using Initializing EPROM's on Vacuum Displays only. Also see other methods before using this one.
1) Switch off machine
2) Remove MPU board and swap U-12 & U-15 with INITILIZING EPROM's
3) Replace board
4) Switch on and wait about 30 seconds for initializing sequence to complete.
5) Switch off
6) Replace original MAIN EPROM's
7) Replace Board & Switch on.
Method 2
Use this procedure if the machine is equipped with a door distribution board number: AS-3356-74
1) Switch off machine
2) Remove the J-1 connector on the door distribution board.
3) Jump pin 5 and pin 11 together.
4) Press and hold the pseudo coin button on the door distribution board
5) Switch on and wait until the win meter displays "CH" before releasing the button.
6) The win meter display should change to "CL" and all the buttons should flash.
7) Switch off and return J-1 connector.
Method 3
Use this procedure if the machine is equipped with MPU chips ME600002-T to ME600002-Z at U-12 & U-15.
1) Switch off machine
2) Install jumper J-14 on the MPU board.
3) Press and hold the pseudo coin button on the door distribution board.
4) Switch on & wait until the win meter displays "SF" the push the test button on the MPU board.
5) The win meter display should change to "CL P" and all the button should flash.
6) Switch off and remove J-14.
Method 4
Use this procedure with main programs ME600002-T to ME600002-Z
1) Switch off machine
2) Remove J1-15 on MPU and place on J-14
3) To clear all RAM , including game options , depress and hold the pseudo-coin button ( not if options must stay )
4) Switch on
5) When the "SF" or "SAFERAM ENABLED" message appears , quickly sepress the test button. Releas the pseudo button.
6) IF performing a ALL RAM CLEAR - Switch off when "CL" or "SAFERAM CLEARED" appears.
7) IF performing a RAM CLEAR , but save options - Swicth of when "CL P" or "OPTIONS SAVED" appears.
8) Replace J-14 to its original position.
9) Switch on
10) Game should return to normal door-open condition; flashing lights indicate problems;
FLASH ERROR
1 Main EPROM Checksum error
2 Supplement EPROM checksum error
3 Personality EPROM checksum error
4 Volatile RAM read/write failure
5 NON-Volatile RAM read/write failure
6 NON-Volatile RAM error , Battery removed , ect.
Method 5
Use this method if none of the above worked…
1) Switch off machine
2) Remove your MPU board only
3) Use a Bally 5000 Plus TEST-RIG and insert MPU board
4) Hold pseudo-coin button and press RAM_CLEAR
5) Insert board in machine and reset door open tilt (87) with JP reset
6) Reset Reel tilts
-
So I decided to ramclear it again, now after I get finished I get a alternating 4.6 and ..JP in the WIN window and solid JP in the PAID window. Wouldn't running the clear chips have removed any jackpot that would have been in memory or am I reading this wrong and heading in the right direction?
-
After you see the 46 & the JP hit the reset button on the cpu, black left button on the front of the cpu.....
Greg
-
After hitting the reset button I now have 2 dots in the WIN window and 5334 in the PAID window and 5 in the LAST IN and 0 in the COIN IN windows. Is this the point that I would need a keypad for it or is this the point that tells me that it is still hosed up? I do get the alarm and a 50 when I open the main door and also I get alarm and blinking button & candle when I hit the change/service button.
After you see the 46 & the JP hit the reset button on the cpu, black left button on the front of the cpu.....
Greg
-
Sounds like its booted, hit the pseudo red coin button in the back of the door with door open & see if you can play it.....
Greg
-
Well, the machine works great provided I put credits in thru the pseudo coin button. Hopper works fine too. Any idea on getting the coin comparitor working?
Thanks.
Sounds like its booted, hit the pseudo red coin button in the back of the door with door open & see if you can play it.....
Greg
-
Youre almost there!!! its probably the coin comparator... common. Im assuming you have the cc-62 model which is in most...has a black box with wires attached to your coin mech. on the black box you need a VERY SMALL phillips to adjust the sensitivity of the coin passing through (you did add a coin in the coin comparator right? you need one for it to "compare" to) turn the adjustment knob a few times all the way back & fourth to kinda clean it, then set it farthest to the MINUS... meaning it wont be very sensitive..... then close the door and pray!!
Let me know, sounds like youre almost home....
Greg
-
Yeah, I tried the sensitivity already and no change, replaced the coin just in case. What concerns me is that the 'Insert Coin' is not lighting or blinking (yes, I put new bulbs in). Is there any test I can do for it, either thru the game of with my trusty multimeter?
-
I wish that was the case, I bought another comparator combo on eBay that was posted as tested and working but it changed nothing on my machine. At this point, I have 265.00 into the machine, clear chips, programming keypad, cant put anything more into it and unless something strange happens and I go ahead and try another ramclear and it works, I will be parting it out by the end of the month.
If I DO part it out, do you know what chips I pull off to sell with the reel strips? I know what ones when it comes to IGT S+ or S2000 but not this machine from hell.
Youre almost there!!! its probably the coin comparator... common. Im assuming you have the cc-62 model which is in most...has a black box with wires attached to your coin mech. on the black box you need a VERY SMALL phillips to adjust the sensitivity of the coin passing through (you did add a coin in the coin comparator right? you need one for it to "compare" to) turn the adjustment knob a few times all the way back & fourth to kinda clean it, then set it farthest to the MINUS... meaning it wont be very sensitive..... then close the door and pray!!
Let me know, sounds like youre almost home....
Greg