1
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Pinball Gold S3000
« Last post by Alpha Slot Machines on Today at 06:42:33 AM »Price drop!
$6200
$6200
Welcome to the NewLifeGames.com message forum!
|
1
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Pinball Gold S3000« Last post by Alpha Slot Machines on Today at 06:42:33 AM »Price drop!
$6200 2
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: iGame Lucky Spin WOF« Last post by Alpha Slot Machines on Today at 06:41:08 AM »PM sent Love@2024
Machine is still available........ 3
IGT Reel Touch Games / Re: Lobstermania gets stuck initializing« Last post by Stayouttadabunker on Today at 06:28:44 AM »Okay good...your voltages are checked out ok.... Hmm
Turn OFF the power to the machine. Earlier Qbert pointed out the corrosion to the MPU board. I'm concerned about that as well. That machine at some point in its lifetime, was horribly neglected/stored in a VERY damp place. We need to try to determine if we can solve the Netplex down message before sending out the MPU for repairs. Member Lookes is very good at repairing MPU's that have acid damage from leaking Varta batteries.... that big green one that used to be on the board...someone removed it at some point. A little bit of history...did you see this MPU working before? When did the Netplex messages start popping up? FYI Netplex devices are the printer, progressive displays, topbox LCD computers, and bill acceptors (BV or BA) One can disconnect them one at a time to find out what's causing the error, but you also get messages that they're not connected, and you have to be able to disable/enable the Netplex device, so you don't get that error. That's harder for you to do right now. Let's try simpler things.... with the power OFF, slide out the I/O card on the door panel for the button deck. It's located just behind the top of the panel looking at it with the door opened. If you look at it, it's in there on an angle. I just want you to tug on the metal handle...pull it up about an inch, then slide it back down firm re-seating it onto the pins. The Molex plug that's connected to it in the handle hole is rather difficult to get off....you don't need to remove it as you're only pulling up on the I/O card one inch so you can re-seat it back down. You might have another I/O card on the side of the MPU enclosure. Go ahead and slide that out an inch towards you and firmly re-seat it back into the socket. I don't want you take them out all the way...you don't need to. All we're doing is re-seating them....why? Because sometimes a pin or two gets oxidized...sort of like a car battery terminal from the 80's. The oxidization creates a film of non-conductive junk....so pulling the circuit card off and pushing it back on kind of rubs the oxidization off of the pins and promotes better electrical contact. I need to point out that a machine "getting stuck initializing" could also be software having bent chip legs folded underneath its own chip body. When that happens, it's hard to see whether or not the chip is actually fully inserted all the way down into the socket holes. The only way to check those is to carefully, slowly remove each chip one at a time out of the sockets and re-insert them back in making sure each leg goes all the way down into the socket holes. 4
IGT Reel Touch Games / Re: Lobstermania gets stuck initializing« Last post by kmarrocco on Today at 06:03:54 AM »The red wire is 13.14V and the orange wire is 25.17V.
The meter is set to DC. 5
IGT S and S-plus Reel Games / Re: Unusual game it s plus« Last post by myplayroom on Today at 05:54:31 AM »Thank you never saw one with this type of low jackpot numbers on a 5 line dd
6
IGT S2000 and Vision Games / Re: IGT Pink panther« Last post by Stayouttadabunker on Today at 05:54:20 AM »Open the door, press the little white Test button on the power switch box...it might be behind it too?
Then watching your LCD screen in the Menus, that would be in the "LCD Volume" as you scroll thru the pages. 7
Coin Comparitors and Other Coin acceptors / Re: IGT Double diamond S Plus, coin comparison issue!« Last post by David Walz on Today at 05:42:09 AM »That is a $1 encoder guide. IKE silver dollar The mystery is solved! 8
IGT Reel Touch Games / Re: Lobstermania gets stuck initializing« Last post by Stayouttadabunker on Today at 05:38:42 AM »Yes...that's a good voltage for that pin on that power Molex connector...it's actually fairly strong!
I was expecting that you'd say more around 6.1 volts. Those wires are coming directly from the PSU (Power Supply Unit) up behind the reel shelf on the back wall of the cabinet. Can you take the red probe out of that one and stick probe onto the pin in the hole with the red wire...get that voltage and that then do the orange wired pin. The black probe should always get the ground from the metal floor of the cabinet. May I ask, do you have your multimeter set for AC or DC voltage? Check and make the ribbon cables are firmly seated into their respective sockets. There's one by that power Molex you were just checking, and one on the door for the VFD display. Sometimes if they're not seated right, you get the Netplex Down message. Lastly but NOT any less importantly, try NOT to push in, or remove any plugs, or circuit boards in your machine with the power switch ON. It just takes a second to switch OFF the power.... believe me, you'll save yourself a LOT of headaches and your wallet will thank you.... lol 9
IGT S and S-plus Reel Games / Re: IGT Double diamond S Plus, RESTORATION« Last post by David Walz on Today at 05:37:49 AM »The backside of that coin head looks pretty big, I believe it was still a dollar denom?? That's where I am leaning toward. 10
IGT Reel Touch Games / Re: Lobstermania gets stuck initializing« Last post by kmarrocco on Today at 05:14:41 AM »Thank you for your help. If this is the right measurement point, I am getting 6.57V.
|
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |