Author Topic: half of my button panel seven areon and other seven are off (Read 14377 times)

steven1969 · « **Reply #20 on:** February 08, 2016, 04:58:30 PM »

Quote from: Tilt on February 08, 2016, 04:21:48 PM

Re-download that diagram. I uploaded the wrong one, it was for an older 19"GK. I uploaded one for a 17" GK/I-game. Monitor power comes from P300 on the power distribution box. Your monitor was working in the photo though, did it die?

I know it not working p3 is that the one on the of the distribution that is on the bottom
I traced that wire that goes to the power distribution box and it goes up to the monitor its self

can you send the diagram of the box there's no blown caps are good from power distribution box in side
I have to wait until I get my new power supply box it should cure it

Tilt · « **Reply #21 on:** February 08, 2016, 06:13:14 PM »

So to summarize your machine has coin-in jam & meter's disconnected errors, a bad monitor, and a power supply with a bad cap? A new power supply isn't likely to fix any of those issues, except for you won't have a bad cap anymore. That could be why your output voltage is a bit low at @24.2 VDC, but the machine was still booting with it.

What "box" are you referring to that you want a diagram for?

steven1969 · « **Reply #22 on:** February 08, 2016, 06:26:55 PM »

Quote from: Tilt on February 08, 2016, 06:13:14 PM

So to summarize your machine has coin-in jam & meter's disconnected errors, a bad monitor, and a power supply with a bad cap? A new power supply isn't likely to fix any of those issues, except for you won't have a bad cap anymore. That could be why your output voltage is a bit low at @24.2 VDC, but the machine was still booting with it.

What "box" are you referring to that you want a diagram for?

for the power supply so do think it could be the mpu board would fix the issue
I know the monitor was working I don't think I blew the tube how can I check to see if am getting power to monitor what plug number

Tilt · « **Reply #23 on:** February 08, 2016, 07:38:33 PM »

Here's the cabinet wiring diagram. J300 is on the right. You can check for 120VAC on the blue/brown wires at the beau plug on the monitor shelf. It's J340 on the diagram.

I don't have a schematic diagram for the power supply if that's what you were looking for. There's three or so different manufacturers of them and they're all different internally.

Your meters disconnected/coin in jam error is probably your MPU board, but a bad IO card can also cause those errors. You won't really know until you get the monitor working again so you can see what the machine is doing.

steven1969 · « **Reply #24 on:** February 08, 2016, 07:56:00 PM »

Quote from: steven1969 on February 08, 2016, 03:55:27 PM

Quote from: Tilt on February 08, 2016, 03:16:33 PM
That's the AC power distribution box. Brown wires are Hot, Blue are neutral. Wiring diagram attached. What are you looking for in there?

thanks for the diagrams does one of these wire s run the monitor

because I traced the wires from distribution box one of them go to the power supply box still with blown cap
I have new box coming in from game king slots I hope this would solves my problems

steven1969 · « **Reply #25 on:** February 09, 2016, 04:35:08 AM »

Quote from: Tilt on February 08, 2016, 06:13:14 PM

So to summarize your machine has coin-in jam & meter's disconnected errors, a bad monitor, and a power supply with a bad cap? A new power supply isn't likely to fix any of those issues, except for you won't have a bad cap anymore. That could be why your output voltage is a bit low at @24.2 VDC, but the machine was still booting with it.

What "box" are you referring to that you want a diagram for?

hello am getting 119.2 volts from the power distribution box
on the blue wire am getting 04 volts
=======================================
the monitor plug from the shelf blue wire 00 volts brown wire 00 volts
but getting voltage from distribution tell me what you think

steven1969 · « **Reply #26 on:** February 09, 2016, 05:13:51 AM »

Quote from: Tilt on February 08, 2016, 07:38:33 PM

Here's the cabinet wiring diagram. J300 is on the right. You can check for 120VAC on the blue/brown wires at the beau plug on the monitor shelf. It's J340 on the diagram.

I don't have a schematic diagram for the power supply if that's what you were looking for. There's three or so different manufacturers of them and they're all different internally.

Your meters disconnected/coin in jam error is probably your MPU board, but a bad IO card can also cause those errors. You won't really know until you get the monitor working again so you can see what the machine is doing.

after I got done checking the voltage from the top shelf monitor plug I put the monitor back in now I here chirping noises coming from the monitor
so am going to leaf it as is for now until I get new replacement board from game king slots

steven1969 · « **Reply #27 on:** February 12, 2016, 02:10:03 PM »

hi I just received my new power supply I had out it in but it still wont work but I do still here chirping the fly back

Tilt · « **Reply #28 on:** February 12, 2016, 04:44:29 PM »

I didn't figure it was going to fix anything since your machine booted with the old one. Your +25VDC output is hopefully higher than what it was with the old one though. Next step is to get the monitor going again so you can see what the MPU is doing.

steven1969 · « **Reply #29 on:** February 12, 2016, 05:39:50 PM »

I get 12.3 v from the distribution box to the monitor I still here noises from fly back
then I get 118.2 volts from top of the distribution box

steven1969 · « **Reply #30 on:** February 12, 2016, 07:01:19 PM »

Quote from: steven1969 on February 12, 2016, 05:39:50 PM

I get 12.3 v from the distribution box to the monitor I still here noises from fly back
then I get 118.2 volts from top of the distribution box

I noticed there's numbers on the back of the top self monitor plug witch ones due I check to get right voltage
I should be getting a replacement mpu board soon maybe this will be all working

Tilt · « **Reply #31 on:** February 12, 2016, 08:43:10 PM »

How many pins does your monitor plug have 19 or 25? If 19 the AC voltage is on pins 14 & 15 , if 25 it's on pins 24 & 25. Be careful that you don't short the probes together measuring it. A new MPU board isn't going to fix a chirping flyback transformer.

steven1969 · « **Reply #32 on:** February 13, 2016, 07:49:39 AM »

I have a 17 pin plug the only option there is to replace the Ceronix Model 1793 Chassis

Tilt · « **Reply #33 on:** February 13, 2016, 08:23:55 AM »

It's a 19 pin connector, only 17 are populated. Ceronix will repair that chassis for you pretty reasonably. Give them a call. Used to be a flat rate of $40.00 + shipping.

steven1969 · « **Reply #34 on:** February 13, 2016, 09:05:56 AM »

Quote from: Tilt on February 13, 2016, 08:23:55 AM

It's a 19 pin connector, only 17 are populated. Ceronix will repair that chassis for you pretty reasonably. Give them a call. Used to be a flat rate of $40.00 + shipping.

I got the monitor working but i get theses lines horizontal lines

steven1969 · « **Reply #35 on:** February 13, 2016, 09:19:25 AM »

Quote from: steven1969 on February 13, 2016, 09:05:56 AM

Quote from: Tilt on February 13, 2016, 08:23:55 AM
It's a 19 pin connector, only 17 are populated. Ceronix will repair that chassis for you pretty reasonably. Give them a call. Used to be a flat rate of $40.00 + shipping.

I got the monitor working but i get theses lines horizontal lines

I I get 118.2 volts from brown wire

Tilt · « **Reply #36 on:** February 13, 2016, 09:45:20 AM »

Your AC power to the monitor is good. It has other problems.

steven1969 · « **Reply #37 on:** February 13, 2016, 10:01:50 AM »

Quote from: Tilt on February 13, 2016, 09:45:20 AM

Your AC power to the monitor is good. It has other problems.

so now I get power to the monitor the only thing I see is the horizontal lines so that would mean the video chassis

Tilt · « **Reply #38 on:** February 13, 2016, 10:32:32 AM »

Most likely. Could also have something bad on the board on the back of the crt.

steven1969 · « **Reply #39 on:** February 13, 2016, 01:30:50 PM »

this is what I get so far can I make a adjustment so where

News:

NLG Site Navigation Menu

Author Topic: half of my button panel seven areon and other seven are off (Read 14377 times)