Author Topic: 3300 error code (Read 10065 times)

Jim · « **Reply #20 on:** February 26, 2018, 08:44:24 PM »

when the pinwheel does not rotate one of two things, bad gearbox/motor assembly or one of the three screws holding the pinwheel are too long and are screwed up against the housing assembly, turn the hopper sideways, look between the pinwheel and the housing , shine a light in there you'll see it real quick.

Jim

Contractorblue · « **Reply #21 on:** February 27, 2018, 05:44:30 PM »

Screws look ok going to have to continue to tear apart the rest of the way and check motor and gearbox

Jim · « **Reply #22 on:** February 28, 2018, 08:26:52 AM »

if you suspect the hopper motor assembly is defective, the easiest way to check it out would be to apply power to it and see what happens.

the motor runs off 120vac, so hook up power cord to the motor, use a power strip with a on/off switch and a circuit breaker, this would allow you to turn the motor on and off as you observe the operation.

Jim

Contractorblue · « **Reply #23 on:** March 02, 2018, 05:38:05 PM »

I manualy turned the hopper motor and then tried the power cord like you suggested and was able to get the hopper motor to run reassembled the hopper afterglow cleaning the pivot points of the magnet and the stop placed hopper back in machine turned it on .the reels spun landing on the same bars as oted in earlier post and the hopper ran and paid out the coins error code 3300 went away o thank you very much to everyone who had posted in helping me with my problem. Now that that problem is fixed after replacing the battery when I hit something it pays coins instead of giving me credits it use to give credits before I had the battery problem any help would be appreciated.

rokgpsman · « **Reply #24 on:** March 02, 2018, 05:45:43 PM »

Sounds like you had some old dried-out grease in the gearbox. I don't know if there is a place on the gearbox to add grease/oil, if so you could add a few drops of oil to help keep the grease more liquified. Or maybe now that you have it turning it may take care of itself with regular hopper use.

There could be a setting in your machine's Test/Setup menus that controls the payout going to credits. Have you posted what SP and SS chips you have on your mpu board? Once we know your SP chip number you can get the document that explains all the features of your TEST/Setup menu.

You can find out your SP and SS chip numbers by following these instructions:

http://newlifegames.com/nlg/index.php?topic=2251.msg11326#msg11326

Contractorblue · « **Reply #25 on:** March 05, 2018, 04:46:01 PM »

I was curious if my last post was recieved with my chip numbers and a picture of the computer board.

shortrackskater · « **Reply #26 on:** March 05, 2018, 04:54:18 PM »

No... you need to re-post. It should show up immediately when you press "Post"
If your pictures are too big, you will get an error message. Then you must resize your pictures.

Contractorblue · « **Reply #27 on:** March 06, 2018, 07:00:28 AM »

Ok I'll try this again here are my chip numbers rs3343 and 8845a they're in position u58 and u59 on the board the problem i have is after replacing the battery the machine automatically pays out coins instead of giving credits

Jim · « **Reply #28 on:** March 06, 2018, 08:05:33 AM »

I'm going to step out on a limb here!, need pictures of your machine or board. sounds as if you have a "S" model machine. S+ boards show the SS chip and the SP chip at positions U52 and U-53?? you said yours are at U 58 and U59, plus a "RS" type chip usually indicates a "S" machine and the lack of a SP chip on your board.

regardless, Like I said in my post reply #9, its a setting that is causing your problem. usually after a battery goes dead, some settings revert back to a default setting. check the settings 5_0,or 5_1 or 5_2 in the menus.

before playing the machine, press the cash out button one time, then play the machine and see what happens.

Jim

Ken · « **Reply #29 on:** March 06, 2018, 08:09:19 AM »

You need to set the machine to credit mode.

If there is just the RS chip in there and no GAME PROM then it should be a S board .. I can't remember to much about them .. push the self test switch until you see 1 - 0. Might only be one time but when it is there then press the spin reel button once .. should be 1 - 1 on the display. Close door and hopefully that takes care of it.

If there is a GAME and REEL prom then it will be 5-x and set x with spin reel button to 5-0 for most machines. If that doesn't work then 5-2.

Contractorblue · « **Reply #30 on:** March 06, 2018, 10:01:03 AM »

Ok thank you very much for the posts I was able to turn machine on and press the cash out button once and started playing and when i hit something it gave me credits so it appears after playing it a bit here everything is functioning properly

Jim · « **Reply #31 on:** March 06, 2018, 10:08:02 AM »

you can change that setting so that you would not have to press the cash out button before playing. usually if you press it and do anything for 30 seconds it will revert back to pay from the hopper.

Jim

Contractorblue · « **Reply #32 on:** March 06, 2018, 10:16:12 AM »

That's exactly what it did after i repyed i pressd cash out and started putting coins in and when it hit it went back to paying coins instead of credits so i pushed credit button again and played and when i hit it gave credits i noticed while doing this that the cash out was lit or not lit so how do you say to set it to go to credits always even after youcash out

Badbaud · « **Reply #33 on:** March 06, 2018, 02:54:35 PM »

Tap the test button until you see a 5-1 then tap the spin button to make it a 5-2 then close door, cashout should now stay lit.

Contractorblue · « **Reply #34 on:** March 06, 2018, 04:31:17 PM »

Pushing test button through the compleye cycles didnt see a 5-1 come up how many times do you push test button for the window of 5-1 is suppose to show up

Amechanic · « **Reply #35 on:** March 06, 2018, 04:43:45 PM »

It might come up as 5-0. I just had a DD machine had the 3 options 5-0,5-1,5-2. It should be in the second display from the left?

Contractorblue · « **Reply #36 on:** March 06, 2018, 04:50:52 PM »

I have a sizziling 7 machine my winner paid , credits , coins played are on the right and are stacked

Amechanic · « **Reply #37 on:** March 06, 2018, 04:57:54 PM »

I thought this was for an S+

Contractorblue · « **Reply #38 on:** March 06, 2018, 05:01:21 PM »

Sorry according to previous post they tell me it is a s machine is there possibly a chart that shows the test button sequences

Badbaud · « **Reply #39 on:** March 06, 2018, 05:35:33 PM »

On a S machine reverse the NO and NC wires on the cashout switch.

News:

NLG Site Navigation Menu

Author Topic: 3300 error code (Read 10065 times)