Slot Bally e-series 2315

[filounet]

Hi,

I want to know if someone can provide me with pictures of a slot Bally e-serie 2315 
I would like pictures of the outside and also drawings on the reels to try to restore it
Thank you for your help 

Filounet

[filounet]

Hi,

I'm always looking for information on this machine which is aesthetically incomplete

I try to start it anyway and by testing the Power supply board, I find 0.25 V instead of 5V, the other two tensions are good
I tested the same card on another slot machine and it gives good 5 v so the card is good but I don't know what causes the problem
Thank you for your help 

Filounet

[filounet]

Hi,
Nobody has any idea to help me because I don't understand at all?
Thank you

[Jon]

Okay let me see if I can help first question is this the card in the machine in question second question have you tested the fuse holders to make sure you have your low voltage coming out of the Transformer

[ramegoom]

Looks like your power supply is not screwed down. It could be shorting on the metal frame, causing the circuit to fail.

Remove the board by unplugging both of the connectors and inspect the solder joints between the PC board traces and the connectors. It's a common failure with the original power supply boards to have cold solder joints there.

[Amechanic]

It’s also possible that there is a bad or loose molex crimp connectors on the PS plug. I’ve come to accept that not every machine can be saved. Pick and choose your battles. Sometimes it’s better just to make a parts box.

[Jon]

I will go find the input for the power supply board and send that to you too

[Jon]

These three files will show you the output of the transformer into the fuses and then over into the power supply board test on AC

[filounet]

Hi,

Transformer voltages are good
The fuses are all good
The card works very well on another machine but announces less than 1 volt instead of the expected 5 volt, the other two tensions are good
The Molex connector and its cables are good

I don't understand where can the problem come from?
Thanks Filounet

[Amechanic]

Try unplugging the 2 large molex plugs going to the doors wiring. It sounds like you have a grounded out power wire some where. You could also remove all the boards, MPU, IO and hopper and retest the voltages. If this game has a sound board do the same thing with it. Then if the power supply is acting up you know it’s is the wiring harness. If your voltage is good at this point, then put back one part at a time until you figure out the problem.

[filounet]

Hi,

I tried to disconnect one by one all the connectors but it does not change anything so there must be a grounding somewhere but mystery for now 

[Amechanic]

I would put my money on a bad plug on the PS Board. Try removing each crimp connector one at a time, cleaning them and spreading them open a bit. Then reinstall them and see if that helps.

[filounet]

Alas it doesn't change anything despite this work
Your bet is lost and I am the first one sorry 

[Jim]

try this!,  you have the better of the two types of connectors Bally used on the power supply.

pins 1-2-3-ac in
pins 4-5-6-7-    ground
pins 8-9-10  ac in
pin 11  ground
pin 12  ZC voltage
pin13  +5vdc  red wire
pin 14-15-16-17-18-19-  +10vdc
pin 20  ground

remove the red wire (pin 13 from the connector)  easy to do, just push in the stop and pull out, reshape the stop and re-insert.

this will test that all the other voltages are good and now you should be able to measure the +5vdc and it should be good.

now just trace the red wire in the loom and isolate where it goes,etc.  time consuming, but its the only way.

hope this helps

Jim

[filounet]

Hi,

Sorry for not answering earlier but sick

Thank you for your advice this shows that the tensions are all good
Now I have to look where the problem is on these 2 cables
Have a nice day 
Filounet

[filounet]

Hi,

After a big cleaning, some repairs on the map and mechanically the machine works perfectly.
I am now looking for the real numbers:

M-239-784
M-239-785
M-239-786
M-239-787

And a coin slide assembly
Thank you for your propositions
Have a nice day

Filounet

[filounet]

Hi,

I would like to know if someone can make me the picture of the winnings of this machine because I have not
Thank you