Author Topic: S2000 triple lucky 7's issues (Read 17684 times)

qbert · « **Reply #80 on:** July 31, 2016, 06:54:33 PM »

You will get a lot of extra parts but the price is right from Rudys make sure you get for IGT S2000.
You may have to key this machine.
Clear and Key will reset the machine, you need chips to be able to do this see tagged thread on this forum.

cowboygames · « **Reply #81 on:** July 31, 2016, 07:15:48 PM »

Before buying a replacement I would verify the software on your existing unit. If it's wrong and just chip to replace it, chips are very cheap. In any case, I would get a 45 key and 224 clear chip set and start from scratch before buying anything else, you'll need those chips anyway in the future. Also, try and get all wiring, especially for the jackpot reset switch, back to factory build.

Hogwild6161 · « **Reply #82 on:** July 31, 2016, 07:34:51 PM »

I will get the chips first, and go from there. Ive seen a couple videos and read up on it on this forum on how to do it, and will give it a shot.

Amechanic · « **Reply #83 on:** July 31, 2016, 07:55:22 PM »

The clear chip is used to wipeout the current setting. The key is used to change settings. There a things that can be changed without these, but if you want to change your machines win percentage, or denomination you need them. Do you know if your MPU board still has the green battery attached to the board? They tend to leak acid damaging the main board causing issues and errors.

Hogwild6161 · « **Reply #84 on:** July 31, 2016, 08:27:14 PM »

Does it have to be the 45 key? Trying to find somewhere on the net that sake the pair, but not having much luck.

cowboygames · « **Reply #85 on:** July 31, 2016, 08:34:04 PM »

Contact member RB, he may be able to help you out with those chips

brianfink · « **Reply #86 on:** August 01, 2016, 12:55:17 PM »

When you get to the auto config screen are you pushing spin reels again to perform the auto config? If you are then your BV is probably bad or has wrong software. As for the bad rig job check to see if there is a spot next to the 4th reel near the front where you can put a cherry switch your picture cut off just a little low of where it should be. attach the wires for the door optic normally open and the service light normally closed. You can probably use the switch you already have. I'm not shore what is plugged into that switch now but you can probably just disconnect or splice that together.

Hogwild6161 · « **Reply #87 on:** August 01, 2016, 05:38:30 PM »

I'm pretty sure all that toggle switch is, is a jackpot reset toggle switch, due to the key on the side doesn't work, and when I flip the toggle switch, the call attendant light comes on top, and I can do a few tests, but only a few. Cant get into autoconfig, either. It just isn't there, when I toggle that switch.

Hogwild6161 · « **Reply #88 on:** August 01, 2016, 06:38:51 PM »

Here's a pic of the inside, of the reset key. Does this need to be replaced, or can this be used?

Hogwild6161 · « **Reply #89 on:** August 01, 2016, 06:40:33 PM »

Here it is.

qbert · « **Reply #90 on:** August 01, 2016, 07:20:13 PM »

That key switch is not all there. Replacement needed

Amechanic · « **Reply #91 on:** August 01, 2016, 08:01:00 PM »

Do you have the key to the reset lock? Here is a picture of what it should look like.. I just picked up a couple spares myself.

Hogwild6161 · « **Reply #92 on:** August 01, 2016, 08:05:17 PM »

Yes, I have the key, and am shopping for the reset lock right now. Thank you for the pics, it helps a ton!

brianfink · « **Reply #93 on:** August 02, 2016, 07:59:30 AM »

Here is a picture of where the switch should go and how it should be wired. You just need the red from the door optic and the green from the cabinet optic, you don't need the optics at all. Sorry about the picture quality.

Hogwild6161 · « **Reply #94 on:** August 03, 2016, 03:33:49 PM »

Thanks everyone for the help. I ended up taking it to a board member on here, RB, to get it all fixed. I will, or he can, give all the details on what exactly it was. I had no idea that someone that could fix them lived so close!

Amechanic · « **Reply #95 on:** August 03, 2016, 03:55:57 PM »

We're all over this country..

qbert · « **Reply #96 on:** August 03, 2016, 04:16:39 PM »

Are you kidding. We are world wide

qbert · « **Reply #97 on:** August 03, 2016, 04:25:21 PM »

RB
Aside from optics and jackpot wiring what did you find?

RB · « **Reply #98 on:** August 03, 2016, 06:17:33 PM »

The optic bypass job was garbage as I suspected. The BV was ID023. Should be 024. I updated it & it works. The reel strips are surprisingly nice. Cleaning up the wiring, getting rid of unneeded wires left by casino as usual. Cleared it & set it up properly. MPU works fine. Replaced the coin battery & going to remove the Varta. Missing screws, etc here & there. Has an old power supply (1998) but it works. It's a 2006 machine. It wasn't even screwed in. Old Ithaca printer also not fastened. Looks like somebody robbed it & put some older parts in. Got it working now but still have several minor details to take care of. The sound amp was bad after I got it working. I will have it ready in a day or two. Charles is a nice guy. I don't get a chance very often to meet another member face to face.

qbert · « **Reply #99 on:** August 03, 2016, 06:27:32 PM »

Glad everything worked out

News:

NLG Site Navigation Menu

Author Topic: S2000 triple lucky 7's issues (Read 17684 times)