11
IGT S and S-plus Reel Games / IGT slant top display board foam
« Last post by David Walz on Today at 06:05:55 PM »IGT slant top display board foam is crumbling. Does someone have an idea what replacement is available?
Welcome to the NewLifeGames.com message forum!
|
11
IGT S and S-plus Reel Games / IGT slant top display board foam« Last post by David Walz on Today at 06:05:55 PM »IGT slant top display board foam is crumbling. Does someone have an idea what replacement is available?
12
IGT I-Game and Game King / GKB00036 to a 044 DEV BOOT« Last post by Ocitown on Today at 06:02:10 PM »Hello NLG!
I hope this is the place to ask for support, my ultimate X poker is dated 12/2003 and I had the CRT upgraded to a quality flat screen when I got it about seven years ago when it worked great. Now the only thing my screen shows is a GK SHA failure check and replace flash. It has not been booting for a couple years now and I decided to get it going a few days ago, I tested the battery and it was dead so I replaced it and also pulled the GKB00036 chip and clean the pins to no avail. I spoke to a nice gentleman on the phone from NLG who said to register here and ask about a replacement 044 DEV boot chip, which was suggested to most likely resolve my issue. Any suggestions would be greatly appreciated at this point, the GPU cooling fan was screaming, so I pulled it out and ordered a new one so it should be ready if I can solve the big issue. Thank you so much for any and all suggestions and support. Ocitown 13
Requests for PSRs, technical information. / Re: Triple Double Red White & Blue« Last post by Operatortony on Today at 05:50:44 PM »Picture of my machine
14
Bally Electromechanical / Re: Bally 809-N« Last post by shortrackskater on Today at 04:42:08 PM »Thanks, I am surprised I didn't already light myself up I was able to reduce the video size, super grainy, turn up the volume to hear the struggle. thanks again There is no video showing. It's only 49kb size. You need to post it on YOUTUBE, then put the link here. 15
IGT S and S-plus Reel Games / Re: haywire deluxe chip change (will it reset existing options selected?)« Last post by whyz1slot on Today at 04:07:34 PM »Right on.....thanks
16
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / WMS BB3 H18.01 OS« Last post by sstiglich on Today at 03:57:22 PM »Hi all, I am having a problem with an 18.03 OS card and getting a game to load, and I am wondering if it's the OS image causing issues. Does anyone have a cheap source for a H18.01 OS I can buy? I've found them for $50, but I really am not too sure this is going to fix anything, just want a cheap test to rule out the cause of my BB3 issue.
thanks Steve 17
Bally Alpha Reel Games / Re: Color flickers with different tints« Last post by Tilt on Today at 03:55:37 PM »Ron has retired from the slot hobby and hasn't been on since 2022, so you probably won't get a reply to your post unless maybe someone else has had that same issue. If replying to an old post like this it's really best if you find out when the original poster(OP) has last logged on. You can do that by clicking on their name. If it's been a long time then start your own topic.
18
WMS Williams Video / Re: Looking for NXT3.2 Bios NBOT-00003-2010 (or even close)« Last post by sccarlso on Today at 03:49:19 PM »Ya, game works great, all except the Gamefield touchscreen is showing proper vertical calibration marks, but is actually set to be horizontally formatted.
I have an actual Gamefield touchscreen from Ceronix, so it should have a "portrait" mode setup touch controller so the touchscreen is in alignment with a vertical video screen. Alas, it isn't. And I don't even know where to start about getting the touch controller to align as it should. Especially when it's an actual Gamefield touchscreen... I have no idea if it's a screwup by Ceronix and hardcoded in the touch controller, or if it's a jumper or setting somewhere, but I've not been able to find any info on how it would be done. If it is a setting hardcoded by Ceronix, then screen goes back so they do it right! As all Gamefield touchscreens are supposed to be in "portrait" mode for the touch controller. Apparently it would be easy to fix if it was just a plain old Linux machine. lol 19
WMS Williams Video / Re: Looking for NXT3.2 Bios NBOT-00003-2010 (or even close)« Last post by idesign on Today at 03:20:44 PM »Iron man S85E-000-1020 is listed as H18.02. There were 3 versions of Iron Man, 1000, 1010 and 1020. You have the last version of that game.
I had that game playing on my converted BB2 with a NEC 32 up top and a Kortek multires below. The game set up fine and played great until I hit the pick bonus. The tocuh screen then went dead. Also was using the NBOT 3-2010 BIOS. Typical of the GF games It always reverts to max bet but that was ok. 20
Bally Alpha Reel Games / Re: Bally Black and White Jackpot Quick Hits« Last post by kmarrocco on Today at 03:14:38 PM »Thanks for the reply. Apparently I was not waiting long enough. As I was taking a picture of the call attendant screen and compressing it, the message switched to prompts to setup the machine. See attached.
So it seems that I am ok now there. I just need the actual touch screen to work now. I have dropped it off with a local shop in hopes that they can repair it. Fingers crossed... |
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |