Author Topic: IGT Vision Tripple Diamond (Read 18138 times)

Painkiller2014 · « **Reply #20 on:** February 21, 2015, 06:09:22 AM »

With this Board and The Chips from the Photo the Machine was still running !!!!
Also the Display the Display schow the Weels an runs!!!
Than come the Ram Error and i dont know maybe that was Credits on the Machine

Painkiller2014 · « **Reply #21 on:** February 21, 2015, 06:15:16 AM »

There was no Bonus Reel or something the Same Picture as on the Rollers was in the Display
I have Play with my Doughter and than Comes the Tilt

qbert · « **Reply #22 on:** February 21, 2015, 06:58:32 AM »

OK guys so we know it is just a regular DD, the display would show the same thing as the reels when playing and it worked just fine with the ss chip combination that was originally pictured so lets stop patting ourselves on the back on how good we are and help get this machine up and running.

Would a bad top box battery do this? I only have experience with reel touch machines so I'm a little blind here.
I know reel touch has some ram chips in the top box that need to have the contacts cleaned up some time to bring it back to life.
I have never seen the ram chips on the MPU go bad other than physical breakage from bad handling so I don't think that is the problem.
Where do we go from here?

Rich

therockinelvis · « **Reply #23 on:** February 21, 2015, 06:32:47 PM »

This may sound very dumb, but I have had people do this. When you turn the key and it tells you to push test button, are you pushing the little white button on the front of the circuit board tray? I have had people say they were pushing the button when they were pushing the large cherry switch that turns the inside light on and off. Are you getting to the point where it says push button? Does it then say close main door? Anything after that? Take a video and post it so we can see what steps you are taking. This is normally a very simple procedure. Confusion does happen. We want your machine fixed as much as you do.

Painkiller2014 · « **Reply #24 on:** February 25, 2015, 10:15:07 AM »

Ther is no reaction ore that the Display says push the Diagnose Button.
I turn the machine one she says Ram Test after that she write Ram Error Crc Game Eprom Mismatch and then turn the Key some ctitical Data will be lost
And than Start the Machine new and the same beginns

qbert · « **Reply #25 on:** February 25, 2015, 10:42:16 AM »

When you get some critical data etc. You must turn the key again then when the next msg comes on the display turn the key again. Keep doing this until the display says press the button for 3 seconds. Hold the button for about 6 seconds close the door and then it should reboot on it's own.

Tell us what happens after doing the above.

therockinelvis · « **Reply #26 on:** February 25, 2015, 11:30:52 AM »

Like Qbert said. Turn the key several times until the display say's push test button for 3 seconds. The display will then tell you to close the door

Painkiller2014 · « **Reply #27 on:** February 26, 2015, 07:46:36 AM »

Hey guys the Machine is running!!!!
After 300 Times Reset with the Key the machine is still alive!!!!
I must make a Setup does anyone have a instruction for the Vision machine?
Stand allone with coins and notes .
I have see the Monitor write good luck but as the machine was running the Monitor Show the same Pictures like the reels ??
I have a Instruction from the Casino but i dont know it is the reight one
Can anybody help me or send me a instruction??
Thansk a lot !!
Greetings

qbert · « **Reply #28 on:** February 26, 2015, 08:44:34 AM »

Open the link on the first post I put on this string.
When you open that link there should be a PDF file explaining the set up after a clear.
Let me know if you can get to that PDF and see if that will help.
Almost there now glad you got it going.
Rich

qbert · « **Reply #29 on:** February 26, 2015, 09:03:03 AM »

Most of the instructions you have look good, but if you have coins and hopper you must change 7.1.5.2 from coinless mode "enabled" to coinless mode "disabled" to be able to use coins. You will need your key chip to change this and remember there must be zero credits on the machine for the key chip to work properly.
Also you will need to change the hopper limit from 0 to a larger number like 800.

Let us know how things go.
Rich
.

Painkiller2014 · « **Reply #30 on:** February 26, 2015, 09:08:19 AM »

Ok thanks
Key Chip is the Key 17??Right??
Do you know what i must adjust that the Monitor Show the same Picture like the Reels?
Is the Setup from you the same like the s2000?

qbert · « **Reply #31 on:** February 26, 2015, 09:17:38 AM »

Key 17 should work. Standard S2000 set up should work.
I have limited experience with vision machines so others here my have to take over. I would think if you have all of the original chips installed it should just come up and start working on the vision monitor. I do not know of any special settings that you must change to make the monitor display the wheels.

Rich

therockinelvis · « **Reply #32 on:** February 26, 2015, 10:47:57 AM »

Remember you have to have zero credits to set up the machine. When you get to "Limits" set high like 9000 and BV to 3000, set your denomination and turn on/off hopper, printer. If your machine played "Good Luck" and showed the reels spinning before then it will again, which must be the reason you have a different SB chip than usual. I will have to go back to the beginning of this post and write that # down for future reference. Great you got it. We're going to miss your posts. haha If your able, I would like to know what files are on your monitor card. It should have "ATA" "BGM" numbers on card in top slot

Painkiller2014 · « **Reply #33 on:** February 27, 2015, 07:39:44 AM »

Here the Fotos from My Flash Card

qbert · « **Reply #34 on:** February 27, 2015, 08:02:55 AM »

Were you able to key the machine?
What is the current status of the machine?

Painkiller2014 · « **Reply #35 on:** February 27, 2015, 09:29:50 AM »

The Machine works i Need some fine adjust.
I can Chose of some Bonuses
Becouse i dont know what Bonus is the right that i can see the same Pictures as the reels

Painkiller2014 · « **Reply #36 on:** March 02, 2015, 10:10:44 AM »

Next Problem
I make the Setup and all thinks are olright becouse if i pull the Plug wait a few of minutes and turn the machine on again it Comes the same Error !!!!Ram Error !!! :banghead:I have Change all batteries make a Ram Clear and a new Setup but ist Alwaiys the same after a Time with no Energie Ram ERROR!!!

What can be the Problem??

Greetings

qbert · « **Reply #37 on:** March 02, 2015, 08:01:36 PM »

There is a battery in the top display have you changed that one?

therockinelvis · « **Reply #38 on:** March 03, 2015, 05:42:23 AM »

Ram error usually comes from changing chips. Check your solder joints on MPU battery. The top box battery won't cause this. The only advice I can give on your bonus screen is to try all the different bonus settings until you find the one you want. I was searching in settings and found bonus settings and saw like 10. I left it alone. All my visions have the bonus play and don't use a SS chip

Painkiller2014 · « **Reply #39 on:** March 03, 2015, 11:38:54 AM »

May be the ss chip is the Problem
I have borrow another board and will try first give the ss chip out and look what hapend
Than i try the othe board with my Chips

News:

NLG Site Navigation Menu

Author Topic: IGT Vision Tripple Diamond (Read 18138 times)