Pages: 1 ... 6 7 [8] 9 10
71
« Last post by mboessen on Yesterday at 07:30:32 AM »
Hi, Badbaud!
You already come recommended by a previous post! Thanks for your reply.
Before I get into service manuals and troubleshooting, I would like to have some idea where this is going financially. It looks like I need this "coin hopper" sub chassis, and probably a stand before I can even start. Can you give me at least a WHAG what the cost will be and what is the likelihood that I will be able to obtain these missing components? I know nothing about these machines, and I'll need to give Mark some idea before I start on it. I'd rather not get immersed in the project only to have my customer say he doesn't want to spend what it will take to get it going.
I won't lie, the machine looks pretty intimidating, and has been stored in a damp basement for years. I really like a good challenge, but I'm trying, in my old age, to learn to look before I leap.
Best
Mike
72
« Last post by bidault on Yesterday at 07:26:36 AM »
Sorry for the delay I was travelling abroad. I checked the voltage at the power supply plug CN-4 it's OK 34V. I checked the white plug on the right side of the coin comparator following the wires from the red keyplug, no voltage betwin the blue and violet wires (picture). There is a lever breaking the photo eye on the the key lock system of the door (picture)
73
« Last post by David Walz on Yesterday at 06:28:12 AM »
Thanks Sunrise Side for spending time with me trying to get the bill acceptor working. Between us both we verified that the wiring is correct as per the electrical drawing. I don't know where I can go from here.
74
« Last post by RobinAK on Yesterday at 06:24:00 AM »
Ahh, yes, I see the difference in the Crystal series. Basically the Crystal Dual looks like the G23 but runs Fam20 games? Did they do away with most of the physical buttons? So the screens are 27" and the topper can be a 3rd monitor?
Crystal dual 23 is 23" screens. Dual 27 is 27". I have a dual 23. Its big enough for me. The 27 looks sweet but it also costs more. Yes they run Fam20 games. The button deck is a touch screen. Ive seen them with either one large spin button on the right side of the screen or two (one on each side). Mine has just one button. Yes the topper is a monitor. So it changes with what game is loaded. Most games it will have video topper action. Some games its just displays a static image on the topper. The topper is 24". It was made for a 27 or curve. But it mounts right up to the 23". They didn't make a video topper for the 23". The cabinet itself has led lighting along the sides that changes colors with game play. The topper also has edge lighting around it. As far as costs goes. Yea its not cheap to ship stuff up here but it is what it is. Far cheaper to have a machine in my game room than flying to Vegas and feeding the machines in the casinos lol.
75
« Last post by Badbaud on May 17, 2024, 11:17:03 PM »
suspect the power supply
76
« Last post by David Walz on May 17, 2024, 08:22:29 PM »
The manual will have the dipswitch settings for the MPU. But I don't think that is your issue. BV stopped after receiving a different MPU. I think the gray wire has to be moved to work with the board you now have. Not sure which pin it has to go to?
Right now this is where the gray wire is located. This has become a nightmare.
77
The manual will have the dipswitch settings for the MPU. But I don't think that is your issue. BV stopped after receiving a different MPU. I think the gray wire has to be moved to work with the board you now have. Not sure which pin it has to go to?
78
« Last post by David Walz on May 17, 2024, 07:47:41 PM »
MPU Dipswitch. But the problem is still it accepts bills and doesn't give credits?
What is the dip switch settings on the MPU supposed to be?
79
MPU Dipswitch. But the problem is still it accepts bills and doesn't give credits?
80
« Last post by 61Wally on May 17, 2024, 07:21:24 PM »
I removed the resistor and installed battery everything was working great. I Actually built up credits and played for hours. I unplugged the machine to move it and when I plugged it back in and turned it On, Only Fluorescent lights came on. It appears I’ve lost the lower Voltage(s), Nothing comes to life. No door buzzer, display. I don’t have any schematics for this machine, Any suggestions where to start my troubleshooting?
Pages: 1 ... 6 7 [8] 9 10
|