Author Topic: BB1 Reels O Dublin credit set up (Read 2966 times)

rickhunter · « **Reply #40 on:** August 16, 2020, 05:19:48 PM »

I would unplug and plug all the "ethernet" looking cables. Maybe they are loose? Also trace those same cables. One of them just connects one side of the front door led digit boards together (so it is basically a short cable going from one plug to the other). Another cables goes down into the animator button connection. And the other cable goes to the spn lamp matrix board that should be on the left side of the cabinet around the reel area. Then there's a cable going from that spn lamp matrix board to the spn hub that is under the reels. Then there's a plug that goes from under the reels to the spn connector on the backplane next to the touchscreen port.

br549autosales · « **Reply #41 on:** August 16, 2020, 06:45:28 PM »

Thank you sir, I will check all of that when I get home tomorrow, at least we are getting close

br549autosales · « **Reply #42 on:** August 18, 2020, 12:20:52 PM »

How do I remove the far left reel assembly so that I can check the cable behind it?

rickhunter · « **Reply #43 on:** August 18, 2020, 12:34:31 PM »

There's a plastic tab on the bottom right of the reel. Slightly lift up on it and at the same timen pull the reel forward using the metal tab that has a black rubberized handle on it.

br549autosales · « **Reply #44 on:** August 18, 2020, 12:38:17 PM »

I unplugged & plugged back up all of the CAT5 cables & now it's working great! Thanks for walking me thru all of that guys

br549autosales · « **Reply #45 on:** August 18, 2020, 10:28:26 PM »

Well it worked for about an hour. I walked away from it and came back 30 minutes later & it had call attendant on the small touchscreen. Could not get it to display what the error message was so I did a clear & cleared just fine but when I put my my OS card back in & turned the machine on the small display does not start booting up, just stats black. I know it's got power because when I turn it on it first shows up as "no signal" but it goes black after that & don't go thru the boot sequence. All of the LEDs are lit on the motherboard & the CPU board

br549autosales · « **Reply #46 on:** August 19, 2020, 09:45:35 AM »

Could this possibly be a power supply issue?

rickhunter · « **Reply #47 on:** August 19, 2020, 10:07:47 AM »

If you get no text on the screen I would make sure that you have no loose connections. Also there are leds on the backplane on the upper right area just below the MPU that are voltage indicators. They should be lit green. If they are all lit green, then you most likely have good power. If you have good power and all connections are good, I would try another mpu.

br549autosales · « **Reply #48 on:** August 19, 2020, 10:50:19 AM »

Yes I'm getting all of my green LEDs lit on the motherboard & the MPU

rickhunter · « **Reply #49 on:** August 19, 2020, 11:12:38 AM »

I would try another MPU.

br549autosales · « **Reply #50 on:** August 19, 2020, 11:18:32 AM »

Just did, that got it but now I'm getting an error clearing NVRAM message

rickhunter · « **Reply #51 on:** August 19, 2020, 02:48:09 PM »

what bios chip is on the new mpu and what clear version are you using?

br549autosales · « **Reply #52 on:** August 19, 2020, 03:38:33 PM »

Changed the MPU then was able to get into the settings but when I went to game settings there was nothing t choose for max bet. Now it's not booting after initial power up again. Here is the chip on my MPU: do you need to see that small snap in card on the left side that looks like a memory stick?

br549autosales · « **Reply #53 on:** August 19, 2020, 03:42:49 PM »

br549autosales · « **Reply #54 on:** August 19, 2020, 03:43:42 PM »

Pic 2

br549autosales · « **Reply #55 on:** August 19, 2020, 04:14:46 PM »

Clear card

rickhunter · « **Reply #56 on:** August 19, 2020, 05:45:50 PM »

I need to see the bios, not the memory card. The bios is the 32 pin eprom chip. I have never used clear 1851 for a bb1. I always thought those were only used on bb2's. I could be wrong though. I've always used an 1810 clear or 1350 for bb1's.

br549autosales · « **Reply #57 on:** August 19, 2020, 06:24:13 PM »

My bad, I thought I sent the picture of the chip, I'll try again

rickhunter · « **Reply #58 on:** August 19, 2020, 08:17:10 PM »

I am at a loss. Does the machine display text at all when you power up?

br549autosales · « **Reply #59 on:** August 19, 2020, 10:33:23 PM »

It did yesterday, even got to play it for an hour or so, I'm lost too. No idea what else to try, especially since I'm getting all of my green LEDs on the mother & the MPU

News:

NLG Site Navigation Menu

Author Topic: BB1 Reels O Dublin credit set up (Read 2966 times)