Author Topic: Error code 83-9 (Bally ProSlot 6000) (Read 8950 times)

4cheddar · « **on:** March 25, 2015, 04:34:02 PM »

After a partial safe ram clear, I'm getting a error code 83-9 which = Bill Record. Does anyone know what that means and how to get it removed?

Thank you

Los Pollos · « **Reply #1 on:** March 25, 2015, 06:07:30 PM »

83 is a ram problem, do a complete clear and you should be fine as long as your battery is good.

4cheddar · « **Reply #2 on:** March 26, 2015, 02:16:04 PM »

Thanks Los Pollos,

I did a complete clear and it did remove the 83-9 code but replaced it with a code 31 error (coin-out hopper jam) Problem is I don't have a hopper. Is it looking for one and can it be disabled under machine options?

Los Pollos · « **Reply #3 on:** March 26, 2015, 02:22:26 PM »

If you don't have a hopper you need to jumper the plug as shown.

Los Pollos · « **Reply #4 on:** March 26, 2015, 02:31:46 PM »

better picture

rokgpsman · « **Reply #5 on:** March 26, 2015, 04:09:07 PM »

Quote from: Los Pollos on March 26, 2015, 02:22:26 PM

If you don't have a hopper you need to jumper the plug as shown.

A friend of mine in interested in doing this, does this work on other Bally models?

(I lightened & enlarged the photos so I could see them better)

Los Pollos · « **Reply #6 on:** March 26, 2015, 05:58:00 PM »

not sure, I only know the S6000.

LINDAM · « **Reply #7 on:** March 26, 2015, 06:43:34 PM »

In the 11d menu change 61 to 0002 also make sure 81 is 0000

4cheddar · « **Reply #8 on:** March 26, 2015, 09:10:44 PM »

I made the jumpers for the hopper plug which did remove the code 31 error. I did another clear, changed machine option 61 from (0001) to 0002=printer only and option 81 from (0001) to 0000=no coin acceptor.

Everything lights up after doing the clear and once the reels calibrate, i get two dots in the win paid display, a zero in the credit and credit in display but no buttons light up and the bill validator will not accept any bills??

LINDAM · « **Reply #9 on:** March 27, 2015, 04:19:06 AM »

The 2 dots are just saying that the machine has been off. They will go away after 2 spins. The 0 is what you want to see. in a perfect world your machine should be working now. hope someone else has a thought.

4cheddar · « **Reply #10 on:** March 27, 2015, 06:17:23 AM »

Yes I was hopeful that fixed it. Also the candle is lit up solid, no blinking

cowboygames · « **Reply #11 on:** March 27, 2015, 06:52:07 AM »

As far as the candle, have you pushed the button to see if it's just turned on for change? Tried to insert bills to play it? Checked all plugs on door harness to make sure they are in and snug?

Los Pollos · « **Reply #12 on:** March 27, 2015, 09:52:10 AM »

check to see if the bill acceptor/transport has a chip in the bottom and its installed correctly with no broken pins.....Also follow the wiring harness from the bill acceptor chassis, one set should go to the back circuit board behind the reels and one should plug into a square plug going to the cash box below.

Los Pollos · « **Reply #13 on:** March 27, 2015, 10:07:16 AM »

also with the power on open the door and push the pseudo button a few times on the MPU if you hear the "dings" and the spin button lights up most likely your problem is the bill acceptor. if the spin button does light up you can hit the button to test the reels.

4cheddar · « **Reply #14 on:** March 27, 2015, 11:27:25 AM »

I have tried all buttons, plugs and bill acceptor. The wires circled in the picture, would they just be for another button or maybe they plugged into the coin acceptor when it was used?

The wire harness behind the bill acceptor looked good, I did find two wires that come off of the plug that don't seem to go anywhere. The chip on the bill acceptor looked good also.

I'm going to run through some diagnostic tests and see what that shows.

Thanks for the suggestions:)

4cheddar · « **Reply #15 on:** March 27, 2015, 12:02:40 PM »

The pseudo button did add credits, light the spin button, ding and spin the reels. After closing the door the bill acceptor does it's cycle and then back to where we started.

Still working on tests, thank you Los Pollos

Los Pollos · « **Reply #16 on:** March 27, 2015, 07:26:26 PM »

pull the bill acceptor out and look through the right side and see if all the dip switches are in the up position.

4cheddar · « **Reply #17 on:** March 27, 2015, 07:28:41 PM »

12 hours later and still nothing, but she is the cleanest non-working machine. I ran every diagnostic test and everything works as it should, during the test. When I exit and close the door, the reels spin, bill acceptor cycles and the candle light goes solid. No buttons are lit, bill acceptor will not accept a bill, win paid shows two dots, credit and coin in show a zero.

If anyone has any ideas not mentioned, post your suggestion. At this stage I'll try anything!

Thanks

4cheddar · « **Reply #18 on:** March 27, 2015, 07:31:24 PM »

Los, they are all down in the off position.

Los Pollos · « **Reply #19 on:** March 27, 2015, 08:32:02 PM »

bill acceptor switches are ok, when you say the candle light stays on solid, is that both the upper and lower light ?

News:

NLG Site Navigation Menu

Author Topic: Error code 83-9 (Bally ProSlot 6000) (Read 8950 times)