S+ Multiple errors

[RB]

USA is 37. Set it to 7, turn the key and set the other one to 3. Other than that BV {1} enabled, and set denom accodingly.
Be sure to finish cycling through the menu to save the settings.

[Badbaud]

When doing the hopper test, it's only supposed to eject up to 10 coins then stop.
If yours is NOT stopping, then the hopper optics are NOT seeing the coins going thu them.
Follow the hopper optical wiring back to the beau connector.

The SSR...I don't think anything is wrong with the relay but yeah, the red one would work...it's just a different colored enclosure.
But... there's absolutely no harm in trying as long as you get the wiring back on correctly.
I'm warning you, one wire connected in the wrong location, and your machine is toast.
Take a photo befoe disconnecting.

The SSR contains 2 triacs in series. That way if one triac shorts out the other probably won't and there will be no hopper runaway.

[mwade109]

I went through as instructed and made sure to set the demonetization and country code, Thanks RB, I would never have to do each digit independently, I went ahead and did what I thought to save it. Put my 1137 chip back in, nothing changed, coins work fine, bv still not energized.  I went ahead and put the set chip back in to verify the settings and they look great as in the video.
(sorry about the crappy video, really hard to hold the phone, door lock and door open lever all at once.  I'm sure it is something I am doing or not doing but not sure what.

https://youtu.be/IRfn8CisN5g?si=G4L5zD3SIi5iQ0Mx

[RB]

<0> [15] is not the denom. It's token value. It means you would get 25 credits for one token the way it is set. Denom selection is <6>. I would clear it and start over.

[mwade109]

Thanks, that is the pdf I have been trying to decipher the info from.  I can get back to it tomorrow afternoon but tell me,
at this point, shouldn't the bv be working?( even though I have the credits set wrong)
And how do you get to the different menus to change the denomination? If I am reading it correctly it would be menu 6 ? <6> Not sure how to get to it.

I will clear it tomorrow (getting pretty good at it) and hopefully get the settings correct.  I had to get a new set chip, do I also need a newer ram clear chip?

<0> [15] is not the denom. It's token value. It means you would get 25 credits for one token the way it is set. Denom selection is <6>. I would clear it and start over.

[RB]

Navigate the set chip menu with the test button. If you don't set a denom then the machine doesn't know how many credits to give you when a bill is inserted. It is mandatory. It could be a 5c denom or $5, etc. $20 will yield you the appropriate number of credits for the denom you set. Your ram clear chip should work fine.

[Jim]

since you have a SP 731, use it until you get the machine working as it should, then do what you want.

since you can use the test mode, get to the menu that starts with 5_0-1 or 2
then advance down to number 9, it will be either 1 or 0, if 1 then the bill unit is enabled.
now, get out of that menu, ( at the end of that menu you will see the country code etc.)
advance to where you see a number 6 in the coins played window, the number in the display is the denomination you have it set.
the spin reels button should be lit, but when you press it , it SHOULD NOT ADVANCE THE NUMBER IN THE DISPLAY, if it does, then it is not set properly.
this tells you with out a doubt your settings, period, no guessing.

Hope ths helps

Jim 

[mwade109]

ok, I am still at a loss.  After clearing and pushing the test button with the set chip in, it seems to only be accessing the <0> Section items.  I do not know how to get it to access the <6> section.

And if I'm understanding you correctly, I would think token value would be one from what you explained but the value starts at two. If anyone can help, I am going to be in front of the machine for the next few hours with the screen up thats in the picture as well as having this nlg window open or feel free to call me or text me at 757-500-3810 or post here and I'll see it pretty quickly.  I am really looking to clear this up.  Thanks

Navigate the set chip menu with the test button. If you don't set a denom then the machine doesn't know how many credits to give you when a bill is inserted. It is mandatory. It could be a 5c denom or $5, etc. $20 will yield you the appropriate number of credits for the denom you set. Your ram clear chip should work fine.

[mwade109]

Ok, Although I do have a 731 laying around, I have not tried that.  So far the only SP Chip that I was able to actually enable the bv is a SP1271. I will try the 731 now.

since you have a SP 731, use it until you get the machine working as it should, then do what you want.

since you can use the test mode, get to the menu that starts with 5_0-1 or 2
then advance down to number 9, it will be either 1 or 0, if 1 then the bill unit is enabled.
now, get out of that menu, ( at the end of that menu you will see the country code etc.)
advance to where you see a number 6 in the coins played window, the number in the display is the denomination you have it set.
the spin reels button should be lit, but when you press it , it SHOULD NOT ADVANCE THE NUMBER IN THE DISPLAY, if it does, then it is not set properly.
this tells you with out a doubt your settings, period, no guessing.

Hope ths helps

Jim

[mwade109]

Used set15 chip and 731 chip and the bv works fine. But still need it to work with the 1137 chip.

since you have a SP 731, use it until you get the machine working as it should, then do what you want.

since you can use the test mode, get to the menu that starts with 5_0-1 or 2
then advance down to number 9, it will be either 1 or 0, if 1 then the bill unit is enabled.
now, get out of that menu, ( at the end of that menu you will see the country code etc.)
advance to where you see a number 6 in the coins played window, the number in the display is the denomination you have it set.
the spin reels button should be lit, but when you press it , it SHOULD NOT ADVANCE THE NUMBER IN THE DISPLAY, if it does, then it is not set properly.
this tells you with out a doubt your settings, period, no guessing.

Hope ths helps

Jim

[jay]

Going back to the 1137 Have you tried changing the bill protocol ? I know there are certain themes and game chips that use something other than the standard 23.

[mwade109]

Hmmm... this is the first I ever heard that, don't mind me. I am using SS7721, replacement for original SS7723 (changed for higher % payout) Not sure if that tells you anything  but I am willing to try new settings!

Going back to the 1137 Have you tried changing the bill protocol ? I know there are certain themes and game chips that use something other than the standard 23.

[jay]

If the game uses IDO-022 interface, you need to turn #10 dipswitch on. The software on the chip supports both protocols and #10 is how you set it for either ID-022 or ID-023 protocol.

It won't hurt anything to flip the switch and see if it resolves the issue.

[jay]

Here is a link to the manual
https://www.manualslib.com/manual/2418175/Jcm-Dbv-200.html

[mwade109]

Thanks but this has a mei in it and just like everything else in this machine it is giving me a terrible time getting it out even with the release pulled on top.  I think maybe dinner is needed, will get back to it in about a hour.

Here is a link to the manual
https://www.manualslib.com/manual/2418175/Jcm-Dbv-200.html

[jay]

Sorry know nada about mei.

[Stayouttadabunker]

Your MEI DBV is a ZT1202 67mm...mine's a ZT102 US.
These things are so old I don't know what country yours is made for?
Yours is for 67mm sized paper currency...that's mili-metres...that's NOT American stuff.

[jay]

He did say it was working with the 731 ?? so I am very confused.

[Stayouttadabunker]

You are correct Jay.
He did say that in Reply #29.
I missed that one.

[mwade109]

I only want to use the 1137 chip so that all coins or bills will go to credits and disable the cashout button.
Unless someone else knows another way around it.