Author Topic: IGT Double diamond S Plus, RESTORATION (Read 2640 times)

David Walz · « **Reply #40 on:** April 26, 2024, 07:05:08 PM »

Handle pull disassembly, cleaned up, assembled.

David Walz · « **Reply #41 on:** April 26, 2024, 07:10:11 PM »

I have a worn part on the handle pull, its a stop piece. It would be awesome to locate another one.

Handle stop bumper.

shortrackskater · « **Reply #42 on:** April 27, 2024, 09:19:13 AM »

Quote from: David Walz on April 26, 2024, 07:10:11 PM

I have a worn part on the handle pull, its a stop piece. It would be awesome to locate another one.

Handle stop bumper.

Don't forget our sponsor page. I "arrowed" the ones that might have it.

You can also put a WTB ad in the classifieds.

David Walz · « **Reply #43 on:** April 27, 2024, 11:07:57 AM »

Quote from: shortrackskater on April 27, 2024, 09:19:13 AM

Quote from: David Walz on April 26, 2024, 07:10:11 PM
I have a worn part on the handle pull, its a stop piece. It would be awesome to locate another one.

Handle stop bumper.

Don't forget our sponsor page. I "arrowed" the ones that might have it.
You can also put a WTB ad in the classifieds.

Alan at K-LAR has been a great provider of parts and knowledge. Hopefully I don’t wear out the welcome mat.

David Walz · « **Reply #44 on:** April 27, 2024, 04:29:39 PM »

Front reel glass replaced with NOS from Azslot. It's absolutely stunning.

The pieces that were taped into place in the old reel glass were a PITA to clean the tape off, all of the three were IGT factory original with the numbers.

David Walz · « **Reply #45 on:** April 27, 2024, 06:09:20 PM »

Interior door assembly, getting the wiring harness installed, the old fluorescent light assembly has been removed from the machine for the LED.

David Walz · « **Reply #46 on:** April 28, 2024, 04:55:12 PM »

I got the speaker installed with the cover. I also put a connector making it more efficient if I need to replace the speaker.

David Walz · « **Reply #47 on:** April 28, 2024, 04:58:23 PM »

This panel is in good condition, except for the yellow. I have some GE86 bulbs on order these are obviously burned out.

David Walz · « **Reply #48 on:** April 29, 2024, 11:22:13 AM »

Working on the belly glass, I've noticed that the glass has a issue, its resting on the steel door, so I put down felt spacers to protect it from chipping, breaking.

David Walz · « **Reply #49 on:** April 29, 2024, 11:34:58 AM »

Reels cleaning, setting the tapes in place, I found out from reading the manual about the alignment pins on the reels, for alignment of the tape when replacing them.

David Walz · « **Reply #50 on:** April 29, 2024, 05:54:00 PM »

Reels installed, wiring harness routed, the reels are secured by the wiring plug coming in from the bottom of the reels. The inside door panel installed, the light is attached to the inside of the panel, I installed LED lights.

David Walz · « **Reply #51 on:** April 30, 2024, 08:46:56 AM »

Decals.

David Walz · « **Reply #52 on:** April 30, 2024, 08:49:00 AM »

More work cleaning, handle installation, reset lock installation,

David Walz · « **Reply #53 on:** April 30, 2024, 03:47:37 PM »

Now this is awesome, the reels are in place and each o e is labeled.

David Walz · « **Reply #54 on:** April 30, 2024, 07:44:13 PM »

MPU service, cleaned the part, being real careful, installed the part, and plugged the wiring harness into the part.

David Walz · « **Reply #55 on:** April 30, 2024, 07:45:57 PM »

MPU service.

David Walz · « **Reply #56 on:** April 30, 2024, 07:49:51 PM »

Putting it back together.
I have a couple of plugs on the door that don't go to anything.

Stayouttadabunker · « **Reply #57 on:** April 30, 2024, 08:23:25 PM »

Zip-tie them back up into the door harness.... you may not need them.
The harness with the black Molex, is for a multi-line reel glass display panel.
The other smaller harness with the rust-colored connector is for... I don't recall what it's for, but you don't need it right now.

David Walz · « **Reply #58 on:** April 30, 2024, 08:32:08 PM »

Quote from: Stayouttadabunker on April 30, 2024, 08:23:25 PM

Zip-tie them back up into the door harness.... you may not need them.
The harness with the black Molex, is for a multi-line reel glass display panel.
The other smaller harness with the rust-colored connector is for... I don't recall what it's for, but you don't need it right now.

Thanks will get it buttoned up. Nice to see you are checking up on me.

David Walz · « **Reply #59 on:** April 30, 2024, 11:26:00 PM »

Working on the MPU.

News:

NLG Site Navigation Menu

Author Topic: IGT Double diamond S Plus, RESTORATION (Read 2640 times)