Author Topic: S2000 Call Attendant,Door Open MB,Bill Stack validator ERROR (Read 8472 times)

qbert · « **Reply #20 on:** April 05, 2019, 08:20:59 AM »

Bunker I don't think this is a vision machine it's a standard S2000 Triple Double Stars.
Your too wrapped up on your vision.
Why do you think it's a vision?
The SB000172 however is not for this game please verify SB chip number

Stayouttadabunker · « **Reply #21 on:** April 05, 2019, 10:05:15 AM »

His chip numbers are what is throwing me off.
Vision SB's begin with 3 or 4 zeros.
Getting into PV1 and PV3 should give him the Game and Base?

MrBreeze 2769 · « **Reply #22 on:** April 07, 2019, 08:28:13 PM »

Thank you for your help....too many pix to post and video to large. Here's the info from Version:
PV1 Game SG000172 D07
PV3 Base SG100272 9665
PV6 Bill WBA-12/13 024 V380-34
PV7 Primary DotM IGT VFD 00007 2000-06-30
PV8 Printer Not Configured
PV9 Printer 2 STPV6.1.1
PV10 Theorectial Payback % LS015462 98.00%
PV11 Proc. Board ID 0-2238-26127
PV13 Spectrum Not Configured
PV14 Version VS011GX1 93B4
PV16 Sound DSV00042 5811
PV17 Aux. Bonus Deviuce Not Configured
PV18 Aux. DotMatrix Not Configured

sixcardmark · « **Reply #23 on:** April 07, 2019, 08:40:19 PM »

PV3 SB100272 2cm triple double stars

MrBreeze 2769 · « **Reply #24 on:** April 07, 2019, 11:39:38 PM »

You are correct i mis-typed
PV3 Base SB100272 9665

Thanks so much for the help

MrBreeze 2769 · « **Reply #25 on:** April 10, 2019, 09:24:59 PM »

Not a vision game,,,,but an upright

Stayouttadabunker · « **Reply #26 on:** April 10, 2019, 11:03:50 PM »

Reply #7 Jim asked if your Bill Validator was flashing 0/1?

Reply #8 bill validator door flashing 0/1

Reply #11 bill validator door showing only a zero - is that sensor still a zero and not flashing anymore?

Also, the guys asked if you ever seen the bill acceptor work?

They're trying to figure out if you have a bad bill acceptor or something else.

If you don't answer, they don't come back.

We want to see you have fun with your machine.

MrBreeze 2769 · « **Reply #27 on:** April 11, 2019, 10:08:06 PM »

I appreciate everyones help,

Processor Test 4.1.3 I never saw the Bill Validator Working, I ran the WBA Units Self Test on it using the dip swithces
Main Door Toggles 1/0
Coin Drop Door 1 Self Test Entire Unit Power Off DIP Switches 123&8 on
Attendant Key 1 Appy Power
Operator Switch 1 Set DIP switch 8 to off,,,, unit cycles and when a piece of paper or bank note inserted WILL NOT ACCEPT
Logic Board 1
Bill Validator Door 0 I did install and CPU and never calibrated WBA
Low Battery 1
Low Battery 2 0

Just Turned on Machine ERROR: Call ATTENDANT,,,,DOOR OPEN B,,,,Paper Out

Top Candle Fast Flash
Bottom Candle Steady Flash

Thank you very much

MrBreeze 2769 · « **Reply #28 on:** April 13, 2019, 01:58:51 AM »

Any suggestions would be appreciated...

MrBreeze 2769 · « **Reply #29 on:** April 19, 2019, 01:08:52 PM »

Still has ERROR dooor open B paper out

Stayouttadabunker · « **Reply #30 on:** April 19, 2019, 08:53:36 PM »

Quote from: MrBreeze 2769 on April 19, 2019, 01:08:52 PM

Still has ERROR dooor open B paper out

Put some paper tickets into the ticket printer.

MrBreeze 2769 · « **Reply #31 on:** April 23, 2019, 02:43:15 AM »

Pardon me,,,,i thought it was understood printer was loaded with tickets,,,thus the unexplained PAPER OUT ERROR while printer full..

Removed tickets from the printer,,,restacked, replaced tickets into the printer, loaded and ticket feed worked properly.

Re Started Machine,,,,,passes display test, spin reels,, CALL ATTENDANT, DOOR OPEN B, & Paper Out ERROR

Thanks anyone for help.

qbert · « **Reply #32 on:** April 23, 2019, 07:19:13 AM »

Opening and closing the door at this point does nothing?
Can you please provide a picture of the printer looking down at the stack of loaded tickets? I would like to see the whole ticket sitting in the printer.

erbs · « **Reply #33 on:** April 23, 2019, 09:42:37 AM »

Check your ribbon cable on your printer. Sometimes the cable gets pinched and cut causing that error.

Amechanic · « **Reply #34 on:** April 23, 2019, 10:22:55 AM »

Quote from: erbs on April 23, 2019, 09:42:37 AM

Check your ribbon cable on your printer. Sometimes the cable gets pinched and cut causing that error.

Not just the ribbon cable, but the curly cables become cracked and start to fall apart. I recently had to replace because it was causing error messages.

MrBreeze 2769 · « **Reply #35 on:** April 23, 2019, 12:05:19 PM »

Iâ€™m ticket printer bin is no where close to full,,Iâ€™m guessing 25%.
Took one pic Tickets removed from printer head.. Red Lite
Next pic ticket loaded
Thank you

MrBreeze 2769 · « **Reply #36 on:** April 23, 2019, 02:20:47 PM »

Ok turned machine off and back on,,,NEW Error code or at least one I havenâ€™t seen lately...
CALL ATTENDANT
DOOR OPEN MB
BILL VALIDATOR STACKER ERROR

Thanks Again

sixcardmark · « **Reply #37 on:** April 23, 2019, 02:33:39 PM »

Re-seat the cash can then close the door to the cash can, then close the main door.

MrBreeze 2769 · « **Reply #38 on:** April 24, 2019, 04:22:59 AM »

Good Morning sir and thank you again for suggestion......
Performed your suggestion First Time,,,,,,waited 30 minutes to see if any changes..(nothing)
Repeated 2 more times no changes...

Thanks Again
David

Jim · « **Reply #39 on:** April 24, 2019, 07:01:48 AM »

I still think your problem is the cash can door switch and associated wiring! that has to be toggling when you check your settings, if not then the machine will NEVER BE ABLE TO RESET THE FAULT CODES and you will continue to get the error messages. both the main door and bill door have to be toggling.

I will look at the schematics to see where your wiring could be open causing the problem.

Can you enter the test diagnostic, with the door open, press the button on the cpu board, this should put you in that mode.

Jim

News:

NLG Site Navigation Menu

Author Topic: S2000 Call Attendant,Door Open MB,Bill Stack validator ERROR (Read 8472 times)