Bally Mastercom, wiring, player tracking...how do I hook it up?

[Yoeddy1]

Check your cables, they must be pin 1 to pin 1.  Bench test your set up with different cables.

You have power to the mastercom?   It lights up?

Didn't you have it working to post the pictures earlier?

Individually, each one works.  No matter which combination of connections that I use, I cannot get them to work at the same time.  I think you may be onto something.  In another thread you told me to order cables from the following website:

http://prowirecommunications.com/store/product335.html

You also mentioned that I needed to specify pin 1 to pin 1.  I did not do that, and it looks like the website ships them as pin 1 to pin 4. 

I guess that's my next step...exchange the cables and specify pin 1 to pin 1 as I cannot figure out for the life of me what to do next.  Is there any way that I could verify if I have pin 1 to pin 1 now to avoid wasting time and shipping charges.

Thanks,
Jason

[bpracer]

Take one of the cables and put both ends in front of so both end are positioned exactly the same.

The wire colors should match 1 to 1, 2 to 2, 3 to3 and 4 to four.

The standard cable is 1 to 4, 2 to 3, 3 to 2 and 4 to 1.

If you look at them exactly you should see what I mean, also look at the short cables you probably got with the card reader or display.

[slots-4-u]

Attached is a text file of the image on the chip.

I don't see the text that is scrolling but you can see text in the file (right hand side).

Does anyone know specifically what address the scrolling text is at?

If I remember correct it's on 1980 & 6170. 1 is for top line & other for bottom. You have to make sure you don't change anything else.

[Yoeddy1]

Take one of the cables and put both ends in front of so both end are positioned exactly the same.

The wire colors should match 1 to 1, 2 to 2, 3 to3 and 4 to four.

The standard cable is 1 to 4, 2 to 3, 3 to 2 and 4 to 1.

If you look at them exactly you should see what I mean, also look at the short cables you probably got with the card reader or display.

These look like the wrong ones?

Jason

[bpracer]

Take one of the cables and put both ends in front of so both end are positioned exactly the same.

The wire colors should match 1 to 1, 2 to 2, 3 to3 and 4 to four.

The standard cable is 1 to 4, 2 to 3, 3 to 2 and 4 to 1.

If you look at them exactly you should see what I mean, also look at the short cables you probably got with the card reader or display.

These look like the wrong ones?

Jason

Yes those are the wrong ones.

[Yoeddy1]

Take one of the cables and put both ends in front of so both end are positioned exactly the same.

The wire colors should match 1 to 1, 2 to 2, 3 to3 and 4 to four.

The standard cable is 1 to 4, 2 to 3, 3 to 2 and 4 to 1.

If you look at them exactly you should see what I mean, also look at the short cables you probably got with the card reader or display.

These look like the wrong ones?

Jason

Yes those are the wrong ones.

Cables sent back to convert to pin 1 to pin 1.  Will update next week.

Jason

[Yoeddy1]

Go the "modified to data" cables back today and both panels are working 100% with one Mastercom 250.  Now I just need to get the custom EPROM going and this project is a wrap!

Thanks to everyone who helped me put this together and for the troubleshooting!

Jason

[ianmcneil68]

Check your cables, they must be pin 1 to pin 1.  Bench test your set up with different cables.

You have power to the mastercom?   It lights up?

Didn't you have it working to post the pictures earlier?

Individually, each one works.  No matter which combination of connections that I use, I cannot get them to work at the same time.  I think you may be onto something.  In another thread you told me to order cables from the following website:

http://prowirecommunications.com/store/product335.html

You also mentioned that I needed to specify pin 1 to pin 1.  I did not do that, and it looks like the website ships them as pin 1 to pin 4. 

I guess that's my next step...exchange the cables and specify pin 1 to pin 1 as I cannot figure out for the life of me what to do next.  Is there any way that I could verify if I have pin 1 to pin 1 now to avoid wasting time and shipping charges.

Thanks,
Jason

Any idea where I can get these cables. The link leads to a company that no longer offers them. I've searched a bit on the internet with not much luck.


Thanks,


Ian

[bpracer]

You can still get them from the link, choose pin 1 to pin one (data) in the drop down choices.

[ianmcneil68]

I did that (it said they were on backorder). When I clicked "add to cart" it said this item is no longer available. Maybe it won't let me order until they're in stock??