Author Topic: 1st time owner IGT S plus issues (Read 3366 times)

craig333 · « **Reply #20 on:** April 14, 2021, 05:28:16 PM »

Quote from: sixcardmark on April 14, 2021, 05:08:45 PM

Starters are FS-2. Coin holder in the CC is spring loaded on backside, the spring probably came off.

Thanks. I did get it to slid back into place, Had to line up to tab with a slot, and it went back int place.

craig333 · « **Reply #21 on:** April 14, 2021, 06:00:42 PM »

Two new starters and my lights are working. I have removed the printed paper. And will order the right glass for it.

Jim · « **Reply #22 on:** April 15, 2021, 09:27:31 AM »

the picture you provided only showed the machine from the reel glass down, what type of top box is on your machine? the glass pictured in your belly glass is actually a 9" award glass that would go up in the top box. Your double diamond belly glass only has the words on it no paytables.

since you turn this machine on and off, do you ever get any numbers in the displays that would indicate that the machine is actually running.

Jim

craig333 · « **Reply #23 on:** April 15, 2021, 09:33:22 AM »

I do have one code 3100. shows 3100 and flash to 1 in a loop. i have read the FAQ for this and have taking out the hopper cleaned and all seems to be working. have done the coin pay out and pay out is right every time. have open and close the door many times trying to clear the code but it will not clear.

on a side note what is the candle light?

craig333 · « **Reply #24 on:** April 15, 2021, 09:47:46 AM »

Full view

sixcardmark · « **Reply #25 on:** April 15, 2021, 10:06:20 AM »

No top box at all!! Guess that explains why the payscale was in the belly glass. You have no candle lite, you have no candle, it goes on top of the top box you don't have.

Jim · « **Reply #26 on:** April 15, 2021, 10:12:34 AM »

that would indicate that the door optics are not working, check to see if the cash can door switch has been bypassed? show us some picture of the wires that are undone. the inside of the machine, especially where the bill unit was.

Jim

craig333 · « **Reply #27 on:** April 15, 2021, 10:49:46 AM »

Some more pics

Jim · « **Reply #28 on:** April 15, 2021, 12:43:37 PM »

in picture 2509, are the two green wires that are on top of the power supply module connected together? pull the cc-16 out of its holder, see if the spring has come off , it puts tension on the slide assembly to hold the coin in place, also see if the rake on the solenoid has been shimmed out . also, with the cc-16 out, remove the cover (it just slides up) from the coin optics, want to see if Q-2 or Q-4 have been removed, pictures again would be helpful.

Jim

craig333 · « **Reply #29 on:** April 15, 2021, 01:39:51 PM »

Quote from: Jim on April 15, 2021, 12:43:37 PM

in picture 2509, are the two green wires that are on top of the power supply module connected together? pull the cc-16 out of its holder, see if the spring has come off , it puts tension on the slide assembly to hold the coin in place, also see if the rake on the solenoid has been shimmed out . also, with the cc-16 out, remove the cover (it just slides up) from the coin optics, want to see if Q-2 or Q-4 have been removed, pictures again would be helpful.

Jim

Yes the two green wires are connected together.
spring has tension.
did not see any shimsQ-2 and Q-4 seems to be in place.

Jim · « **Reply #30 on:** April 15, 2021, 01:50:15 PM »

Since you can get into the test mode, get to the input tests 10_1, scroll in that menu to get to 13_1, while in that test, close and latch the door, when latched, the 13 shouls start cycling from a 1 to a zero, if it stays on a 1 then the machine is not see the door as being closed. if it stay on 1 slowly raise the latch while watching the number, see if it statrs to cycle at a different point!

Jim

craig333 · « **Reply #31 on:** April 15, 2021, 02:06:09 PM »

Well I made a rookie mistake and as I was taking the last pics and checking the CC. I did not turn the power off, I heard a click, I was pulling on the flip you told me to slid up. After I reread and seen to remove the CC then side it up. know I have no display, and not able to run any test mode, top light comes on, and the wheels engage, but not spin.

The click I hard may have been the door moving as I have hard it since then with the power off.

Jim · « **Reply #32 on:** April 16, 2021, 09:04:36 AM »

check the fuses, maybe you shorted something out?

Jim

craig333 · « **Reply #33 on:** April 16, 2021, 04:28:27 PM »

I did have a blown fuse. The top one, i got the CC wire today and hooked it up and changed the fuse. now when I turn it on the wheels spin and 0 shows up in the coin played, after I close the door it spins one more time and displays 1 in the coin played.
1300 code is gone.
Should the grenn light on the CC be lite up? it is not. when I put coin in it just goes into the coin hooper,

sixcardmark · « **Reply #34 on:** April 16, 2021, 07:18:01 PM »

The cc will not lite up when the door is open. Press the tiny white rectangle button on the coin in optics board just under the coin comparator, it should give you a credit. There is also a coin in optics test you can perform. The cc is excepting the coins but the optics is not seeing the coins if they just go to hopper without giving a credit played.

craig333 · « **Reply #35 on:** April 16, 2021, 07:23:08 PM »

Quote from: sixcardmark on April 16, 2021, 07:18:01 PM

The cc will not lite up when the door is open. Press the tiny white rectangle button on the coin in optics board just under the coin comparator, it should give you a credit. There is also a coin in optics test you can perform. The cc is excepting the coins but the optics is not seeing the coins if they just go to hopper without giving a credit played.

Yes I can press the button to get two credits, and play with door open.
I will have to try the optics test.

thanks for the help. i'm getting closer to be able to play the slot,

I will have my new glass for it when I get over work tomorrow, Can't wait to see it installed,

sixcardmark · « **Reply #36 on:** April 16, 2021, 07:32:19 PM »

A normal award (top glass) will not fit in the belly glass spot. What glass did you get?

The optics sensors may just need cleaning.

craig333 · « **Reply #37 on:** April 16, 2021, 07:35:54 PM »

I did order the belly glass off ebay for it.

sixcardmark · « **Reply #38 on:** April 16, 2021, 07:39:28 PM »

That is not a belly glass, it will not fit. That is the award glass.

That also it a double diamond glass, you want double diamond deluxe glass. You have a double diamond deluxe with no top box (where the award glass is supposed to be).

sixcardmark · « **Reply #39 on:** April 16, 2021, 07:49:35 PM »

If you can only get two credits from optics button you need 2 coin glass not 3 coin.

Here's what your machine used to look like:

News:

NLG Site Navigation Menu

Author Topic: 1st time owner IGT S plus issues (Read 3366 times)