91
I'm not exactly sure what you mean by "thinner" but they ARE different...you bought white ones, instead of the ones with yellow background? The OLEDs you've put in may not be the exact same size or resolution as the yellow ones that were originally installed on the deck. I would get two more new white ones because if those yellow ones are original, they will die soon. There's a definite life expectancy of them (about 40,000 hours set at half brightness), and most of it was used up when they were ON in the casinos 24/7.
Do the math....8,760 hours equals 1 year....except a leap year...lol
92
« Last post by mikeyg on May 02, 2024, 05:49:47 AM »
Thanks for the tip. I spoke with Gamblers Oasis and we're all set.
93
« Last post by sstiglich on May 02, 2024, 05:46:18 AM »
I went thru spininc.com and used their contact us email to ask about one. It took a day or two, but they have them, and it was inexpensive. I was already planning on ordering something else, so with the combined shipping it was a super good deal. Hopefully this helps!
Steve
94
ok.... if there's no power going thru the harness to the door bezel, that tells us the validator isn't ready to accept bills.
History, did you ever see this bill head work? The seller didn't mention anything about it not working? I wish I could help you further other than for you to re-check the connections to the bill acceptor harness. Make sure no wires are broken on the harness to the pins.
I don't know anything about a dip switch #6 test. I've never had to check bill acceptors with that. I just make sure the bill acceptors are flashed correctly, the harnesses are good, the bezel lamps aren't burned out, and the acceptor paths and sensors in the head, are clean.
95
Your 1st photo indicates that you've changed the game chip and the MPU is seeing that it's not the correct chip. Did you mess with them? Opening and closing the door a couple of times should erase all "stacked" error messages. Your green and amber LED lights on the MPU are ok....as long as the red one doesn't light up.
Pressing the Test button is only supposed to be for entering programming menus...not for clearing anything - unless you've changed chips. If you're losing settings, your MPU may be suspect. Without me going back thru 120 Reply's, can you post a clear photo of the socketed chips on the MPU? Also, a photo of the green Varta battery and that area. Something is causing that CRC checksum error. That's a major error indicating that the MPU is seeing a possible major programming fault with your Game chip.
Finally, if you disable the bill acceptor, how will you get credits on the machine to play? Does the machine have a coin comparitor mechanism?
96
« Last post by padamez on May 02, 2024, 05:27:39 AM »
I am using a set015 chip cash box has been reseated many times. i verified the denomination indicates 25 and BV is enabled using the test button options. Also, it fails to do anything when I test it using dip switch 6 procedure with transport not attached.
97
A new FUJITSU Cash Handling Component GSR50 is for sale Multi-Cassette Currency Recycling Module it’s the Big One please remember that I am from Austria because of the transport Price 1700$
98
Hmm... What SET chip are you using to enable it? It shouldn't be an issue as the SP731 is a fairly standard SP GAME prom chip and should be enabled by just about any SET chip but I want to verify. The SP731 can use SET05, SET015, or SET017 to modify the denomination and enable/disable the bill acceptor. Re-check and make sure your denomination is indeed set for a quarter and NOT set for zero. This below, is from the PSR731 sheet...>>> Bill Acceptor Enabled, Disabled Display <0> [9] Indicates if the bill acceptor is enabled { 1 ) or disabled (0).Just for the heck of it, you can also try re-seating the cashbox...sometimes that helps get the DBV going.
99
For sale is a set of parts for slot machines. The parts are in mint condition and were only installed in prototypes for testing!! These are 2x JCM IPro-100 1x Mei Advance head, 1x JCM Ivizion complete, 2x Eurocoin 802 TM thermal printer, 1x Custom Tg 2460 H kiosk built-in thermal printer, 1x Transact Epic 880 thermal printer in the last photos you can see the mom prices of the parts be sold used!! For further questions, please do not hesitate to contact me Please think about the Transport I am from Austria Price 1300$
100
I'm not sure what your machine looks like and what it has on it already, but I'm also not able to assist here as I've never done this myself. A good starting point though is this video on YouTube. It names parts and everything you need too, plus everything you need to do each step of the way. If you're able to post in the classifieds, try that. But there's other places you could source parts too. They're out there. Good luck! https://www.youtube.com/watch?v=GH-eA1rM2yc
|