Author Topic: 65 0 Error (Read 6433 times)

Clawsino · « **on:** March 06, 2016, 12:14:45 PM »

I Have an IGT S+ "Chaos" slot machine here I'm trying to get working. When I plug it in and turn it on I get a 65 0 error code, if I close the door nothing changes, but if I press the test button or turn the reset key it goes through the menus. The machine is running a 16mhz board with a SP1027 type 2/21 chip in it. When I first got the machine the battery was dead, I Have since replaced the battery and now have the error. Would I need to run my clear chip?

slots4home · « **Reply #1 on:** March 06, 2016, 12:29:17 PM »

A 65-0 is a bad EPROM device.
I would be sure the game EPROM is seated right and if it is good and still get a 65 code then try the clear

Clawsino · « **Reply #2 on:** March 06, 2016, 01:55:05 PM »

Ok so I tried the clear chip and when the machine powers up I press the test button and it immediatly goes to 65 0

slots4home · « **Reply #3 on:** March 06, 2016, 02:00:22 PM »

It might be a bad EPROM
Was it working before you changed the battery?

Clawsino · « **Reply #4 on:** March 06, 2016, 02:03:00 PM »

I'm not sure, when I got it it never worked, I measured 0v on the battery so I replaced it and I now get the 65 0 error

slots4home · « **Reply #5 on:** March 06, 2016, 02:21:52 PM »

Do you have another reel chip to test to see if the one you have is bad?

Clawsino · « **Reply #6 on:** March 06, 2016, 02:29:22 PM »

I have another reel chip, but I'm not sure if its good. I will give it a try tho

Clawsino · « **Reply #7 on:** March 06, 2016, 02:43:06 PM »

Ya when I put the other chip in nothing comes up on the screen. I put the other chip back in and I get the 61, then I press the test button and get 61 1, close the door and then I get the 65 0

slots4home · « **Reply #8 on:** March 06, 2016, 02:45:21 PM »

I wonder if your game chip is not supported by the 16 mg board
the ones I have used are the 1272 game chip

Clawsino · « **Reply #9 on:** March 06, 2016, 02:54:51 PM »

I also have a few other SP chips. 731, 873, 939,1137 and 1146. I know a couple are type 2 but not sure if they will work on the 16mhz board. I will do some testing

rickhunter · « **Reply #10 on:** March 06, 2016, 04:12:01 PM »

65-0 is bad EEPROM device not EPROM. The EEPROM is the 8 pin chip on the backplane, sometimes this is soldered other times it is socketed, either way you probably need to replace it or just get another backplane.

Clawsino · « **Reply #11 on:** March 06, 2016, 04:19:27 PM »

I have one other backplane and when I put the board into it I get nothing. I beleive I ordered the little chips on the backplane before, not sure if I ever replaced one tho. Is it possible?

Shaggy · « **Reply #12 on:** March 06, 2016, 04:25:32 PM »

Quote from: Clawsino on March 06, 2016, 02:54:51 PM

I also have a few other SP chips. 731, 873, 939,1137 and 1146. I know a couple are type 2 but not sure if they will work on the 16mhz board. I will do some testing

The 1137 is a Tokenization machine chip. Not a type 2 but good for 0,1,4,5 type games and some others. Good to have if you want to tokenize a machine.

Dave

therockinelvis · « **Reply #13 on:** March 06, 2016, 05:07:13 PM »

A little confused. You are getting 65-0. When you push the test button after that, it goes into the menu? It should clear by pressing the test button for 1 second then close and latch the door.

Crash0 · « **Reply #14 on:** March 06, 2016, 06:30:13 PM »

I would say you need a SP-1272 for 16mhz board to start with, the one you listed I don't see, but probably for 10mhz. If that doesn't work then would try reel chip and go from there. As always make sure chips are inserted in the proper direction.

Shaggy · « **Reply #15 on:** March 06, 2016, 06:39:56 PM »

I think he's going to have to use a 1252 as a 1272 is a type 0,1,4,5 chip and he needs a 16mhz Type 2 game chip.

Dave

Crash0 · « **Reply #16 on:** March 06, 2016, 07:29:53 PM »

SP1252 Type 2/21 (Haywire/Haywire Deluxe) 16MHz,
I read wrong 1 sry

Shaggy · « **Reply #17 on:** March 06, 2016, 07:35:29 PM »

No problem. Sometimes these posts can get really confusing and the end result is very likely his motherboard (backplane). But at least we get him going in the right direction.

Dave

Crash0 · « **Reply #18 on:** March 06, 2016, 08:13:24 PM »

Just replaced 2 motherboards, may see if I can fix old ones. was just Bill Validator issues.
Agreed 1 step at a time

Clawsino · « **Reply #19 on:** March 10, 2016, 07:49:22 PM »

Hey guys, just thought i would update this. So I pulled out the back plane and a spare one I have that was corroded. I desoldered the chip off the corroded board and soldered it back onto the good board and when I put it back it I got a 65 2 which was easy to clear and then the game worked! Turns out the chip on the backlplane was faulty

News:

NLG Site Navigation Menu

Author Topic: 65 0 Error (Read 6433 times)