91
IGT S and S-plus Reel Games / Re: IGT Double diamond S Plus, RESTORATION
« Last post by David Walz on Yesterday at 09:14:16 AM »There's a skeleton in your garage! Bad neighbor?
Nope, bad mother.
Welcome to the NewLifeGames.com message forum!
|
91
IGT S and S-plus Reel Games / Re: IGT Double diamond S Plus, RESTORATION« Last post by David Walz on Yesterday at 09:14:16 AM »There's a skeleton in your garage! Bad neighbor? Nope, bad mother. 92
IGT AVP (Including G20,G23) / Re: IGT G20 Button compatibility« Last post by rickhunter on Yesterday at 08:54:39 AM »You may need a newer version of the blackfin firmware for the edgelit buttons.
93
IGT S and S-plus Reel Games / Re: IGT Double diamond S Plus, RESTORATION« Last post by shortrackskater on Yesterday at 08:02:47 AM »There's a skeleton in your garage! Bad neighbor?
94
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: Wts wms bb2 ruby slippers cf game card $65 shipped« Last post by topgun911 on Yesterday at 04:36:05 AM »Pretty sure os H13.11 and higher will work
95
NLG Classified ads and White Sheet - PLEASE READ DESCRIPTION BEFORE POSTING! / Re: S2000 Non working boards« Last post by scottf11961 on Yesterday at 03:43:59 AM »Do you want them? For you, take them all..$60 +. I'm actually getting rid of all my S2000 machines and going a different route with the gameroom. Selling them all. Even my giant Ms Little green men
96
BALLY Game Maker / Re: Could use some assistance on my gamemaker V7200« Last post by SkyPilot on May 05, 2024, 11:26:13 PM »Yes, Chris, seems it's all pretty much "Do it until you figure it out" kinda thing with these machines..
I really appreciate your help!!!! Howard P.S. On the Residual Credit I put "No Gamble" and also, thanks to you, I just entered Coin Acceptor and not the one with COD Board 97
IGT AVP (Including G20,G23) / Re: IGT G20 Button compatibility« Last post by sixcardmark on May 05, 2024, 11:10:52 PM »I have swapped non-edge lit for edge lit buttons on a couple machines with no problems.
98
BALLY Game Maker / Re: Game Maker 7200, Hot Hot Hot setup issue« Last post by Chris-socal on May 05, 2024, 09:29:07 PM »Your settings look ok.
Is this error only one game or it won’t boot past this? You need to switch 7 and 8 99
JCM WBA 10, 11, 12, 13, 14, 20, 21, 22, and 23 Bill Validators / Re: WBA-13 V3.60 not allowing bills past sensor IGT S2000« Last post by lowlimitlootlane on May 05, 2024, 09:21:14 PM »OK, I will go on EBAY, I saw the EPROM software on there. If I install the eprom, and still have issues can I believe it is now isolated to an issue with the head unit? At that point would the head be servicable or trash? Thanks for your help!
100
IGT S and S-plus Reel Games / Re: Payout not matching pay table.« Last post by t28c34 on May 05, 2024, 09:20:49 PM »FIXED! Thanks to Sixcardmark, he sent me a SS6622 chip and solved two problems. I never realized that it did not have the right reel prom installed. Swapped it out and now the pay table matches the reels. Then went to into setup for the bill validator and was able to change and put in the right settings. With the wrong reel chip, setup would not let me change the setting. Machine is now properly working. Thank you NLG and guys that respond to helping out with issues.
|
Cell Phone and Pad Mode imode wap wap2 |
NLG Archives Archives @ newlifegames.net Wayback Machine |
Contact Us NLG Shop 928 754-4147 Email Us 1788 Highway 95 30 BHC City AZ 86442 |